2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1610/13 Front Airbag Sensor RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The front airbag sensor RH circuit consists of the center airbag sensor assembly and front airbag sensor RH.
If the center airbag sensor assembly receives signals from the front airbag sensor RH, it determines whether or not the SRS should be activated.
DTC B1610/13 is recorded when a malfunction is detected in the front airbag sensor RH circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1610/13
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.
  2. Front airbag sensor RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

H002750E34

INSPECTION PROCEDURE


1. CHECK DTC

  1. C114779E01
    Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1610/13 is not output.

    HINT:
    Codes other than DTC B1610/13 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and front airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor assembly side and front airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)

  1. C114792E04
    Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-2 (+SR) - A28-1 (-SR)
    Always
    Below 1 Ω



NG
Go to step 9
OK


5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

  1. C114791E05
    Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-2 (+SR) - A28-1 (-SR)
    Always
    1 MΩ or higher



NG
Go to step 10
OK


6. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

  1. C114791E05
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-2 (+SR) - Body ground
    Ignition switch on (IG)
    Below 1 V
    A28-1 (-SR) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
Go to step 11
OK


7. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

  1. C114791E05
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-2 (+SR) - Body ground
    Always
    1 MΩ or higher
    A28-1 (-SR) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 12
OK


8. CHECK FRONT AIRBAG SENSOR RH

  1. C114793E01
    Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1610/13 and B1615/14 are not output.
    A
    DTC B1610/13 is output. (for 2GR-FE RHD)
    B
    DTC B1610/13 is output. (except 2GR-FE RHD)
    C
    DTC B1615/14 is output.
    D

    HINT:
    Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

D
REPLACE FRONT AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

9. CHECK INSTRUMENT PANEL WIRE (OPEN)

  1. C123715E01
    Disconnect the instrument panel wire connector from the engine room main wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AE4-2 (+SR) - AE4-1 (-SR)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

10. CHECK INSTRUMENT PANEL WIRE (SHORT)

  1. C123716E01
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AE4-2 (+SR) - AE4-1 (-SR)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

11. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

  1. C123716E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    AE4-2 (+SR) - Body ground
    Ignition switch on (IG)
    Below 1 V
    AE4-1 (-SR) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

12. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

  1. C123716E01
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AE4-2 (+SR) - Body ground
    Always
    1 MΩ or higher
    AE4-1 (-SR) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE


← B1610/13 Front Airbag Sensor RH Circuit Malfunction (Oct 2006 – May 2009)B1615/14 Front Airbag Sensor LH Circuit Malfunction (Jun 2006 – Sep 2006) →