B1615/14 Front Airbag Sensor LH Circuit Malfunction
Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.If the center airbag sensor assembly receives signals from the front airbag sensor LH, it determines whether or not the SRS should be activated.
DTC B1615/14 is recorded when a malfunction is detected in the front airbag sensor LH circuit.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| B1615/14 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.

Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1615/14 is not output.
- HINT:
- Codes other than DTC B1615/14 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.
Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged.
- OK:
- The connectors are not deformed or damaged.
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN) |
Using a service wire, connect connectors 30 (+SL) and 28 (-SL) of connector B.

- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A13-2 (+SL) - A13-1 (-SL)
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT) |
Disconnect the service wire from connector B.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A13-2 (+SL) - A13-1 (-SL)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
A13-2 (+SL) - Body ground
Ignition switch ON
Below 1 V
A13-1 (-SL) - Body ground
Ignition switch ON
Below 1 V
|
|
||||
| OK | |
| 7. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND) |
Turn the ignition switch to the LOCK position.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A13-2 (+SL) - Body ground
Always
1 MΩ or higher
A13-1 (-SL) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 8. CHECK FRONT AIRBAG SENSOR LH |
Connect the connectors to the center airbag sensor assembly.

Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- Result:
Result
Proceed to
DTC B1610/13 and B1615/14 are not output.
A
DTC B1610/13 is output.
B
DTC B1615/14 is output.
C
- HINT:
- Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
| 9. CHECK INSTRUMENT PANEL WIRE (OPEN) |
Disconnect the instrument panel wire connector from the engine room main wire.

- HINT:
- The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
AE4-3 (+SL) - AE4-4 (-SL)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 10. CHECK INSTRUMENT PANEL WIRE (SHORT) |
Disconnect the instrument panel wire connector from the engine room main wire.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
AE4-3 (+SL) - AE4-4 (-SL)
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 11. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) |
Turn the ignition switch to the LOCK position.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
AE4-3 (+SL) - Body ground
Ignition switch ON
Below 1 V
AE4-4 (-SL) - Body ground
Ignition switch ON
Below 1 V
|
|
||||
| OK | ||
| ||
| 12. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) |
Disconnect the instrument panel wire connector from the engine room main wire.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
AE4-3 (+SL) - Body ground
Always
1 MΩ or higher
AE4-4 (-SL) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
