B1653/35 Seat Position Airbag Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| B1653/35 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC |
Turn the ignition switch on (IG), and wait for at least 60 seconds.

Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1653/35 is not output.
- HINT:
- Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly, the seat position airbag sensor and front seat inner belt assembly (driver side).
Check that the connectors are not damaged.
- OK:
- The connectors are not deformed or damaged.
|
|
||||
| OK | |
| 4. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN) |
Using a service wire, connect terminals 14 (DSP+) and 13 (DSP-) of connector B.

- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT) |
Disconnect the service wire from connector B.

Measure the resistance between the terminals of connector E according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
1 - Body ground
Ignition switch on (IG)
Below 1 V
2 - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | |
| 7. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - Body ground
Always
1 MΩ or higher
2 - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 8. CHECK SEAT POSITION AIRBAG SENSOR |
Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1653/35 is not output.
- HINT:
- Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 9. REPLACE SEAT POSITION AIRBAG SENSOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the seat position airbag sensor (Click here).
- HINT:
- Perform inspection using parts from a normal vehicle if possible.
| NEXT | |
| 10. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1653/35 is not output.
- HINT:
- Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
- Result:
Result
Proceed to
OK
A
NG (for 2GR-FE RHD)
B
NG (except 2GR-FE RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 11. CHECK WIRE HARNESS (OPEN) |
for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

- HINT:
- The service wire has already been inserted into connector B.
for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).
- HINT:
- The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-2 (LSP+) - N3-4 (LSP-)
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
O24-2 (RSP+) - O24-4 (RSP-)
Always
Below 1 Ω
- Result:
Result
Proceed to
OK (for 2GR-FE)
A
OK (for 2AZ-FE)
B
NG (for LHD)
C
NG (for RHD)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 12. CHECK WIRE HARNESS (SHORT) |
for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-2 (LSP+) - N3-4 (LSP-)
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
O24-2 (RSP+) - O24-4 (RSP-)
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK (for 2GR-FE)
A
OK (for 2AZ-FE)
B
NG (for LHD)
C
NG (for RHD)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 13. CHECK WIRE HARNESS (SHORT TO B+) |
Turn the ignition switch off.

Disconnect the negative(-) terminal cable from the battery, and wait for at least 90 seconds.
for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).
for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-2 (LSP+) - Body ground
Ignition switch on (IG)
Below 1 V
N3-4 (LSP-) - Body ground
Ignition switch on (IG)
Below 1 V
- for RHD:
Tester Connection
Condition
Specified Condition
O24-2 (RSP+) - Body ground
Ignition switch on (IG)
Below 1 V
O24-4 (RSP-) - Body ground
Ignition switch on (IG)
Below 1 V
- Result:
Result
Proceed to
OK (for 2GR-FE)
A
OK (for 2AZ-FE)
B
NG (for LHD)
C
NG (for RHD)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 14. CHECK WIRE HARNESS (SHORT TO GROUND) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).
for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-2 (LSP+) - Body ground
Always
1 MΩ or higher
N3-4 (LSP-) - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
O24-2 (RSP+) - Body ground
Always
1 MΩ or higher
O24-4 (RSP-) - Body ground
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK (for 2GR-FE)
A
OK (for 2AZ-FE)
B
NG (for LHD)
C
NG (for RHD)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
