2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Seat position airbag sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Front seat inner belt assembly (Driver side)
  4. Seat position airbag sensor
  5. Center airbag sensor assembly

WIRING DIAGRAM

C123783E01

INSPECTION PROCEDURE


1. CHECK DTC

  1. C145343E01
    Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly, the seat position airbag sensor and front seat inner belt assembly (driver side).

  1. Check that the connectors are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

  1. C145339E01
    Using a service wire, connect terminals 14 (DSP+) and 13 (DSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω



NG
Go to step 11
OK


5. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

  1. C145340E01
    Disconnect the service wire from connector B.

  1. Measure the resistance between the terminals of connector E according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1 MΩ or higher



NG
Go to step 12
OK


6. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

  1. C145340E01
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Ignition switch on (IG)
    Below 1 V
    2 - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
Go to step 13
OK


7. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

  1. C145340E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Always
    1 MΩ or higher
    2 - Body ground
    Always
    1 MΩ or higher



NG
Go to step 14
OK


8. CHECK SEAT POSITION AIRBAG SENSOR

  1. C145343E01
    Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


9. REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


10. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C145343E01
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE RHD)
    B
    NG (except 2GR-FE RHD)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

END

11. CHECK WIRE HARNESS (OPEN)

  1. C145341E01
    for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

    HINT:
    The service wire has already been inserted into connector B.

  1. for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N3-2 (LSP+) - N3-4 (LSP-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O24-2 (RSP+) - O24-4 (RSP-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK (for 2GR-FE)
    A
    OK (for 2AZ-FE)
    B
    NG (for LHD)
    C
    NG (for RHD)
    D



B
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)

C
REPAIR OR REPLACE FLOOR WIRE

D
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)

12. CHECK WIRE HARNESS (SHORT)

  1. C145342E01
    for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

  1. for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N3-2 (LSP+) - N3-4 (LSP-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O24-2 (RSP+) - O24-4 (RSP-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK (for 2GR-FE)
    A
    OK (for 2AZ-FE)
    B
    NG (for LHD)
    C
    NG (for RHD)
    D



B
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)

C
REPAIR OR REPLACE FLOOR WIRE

D
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)

13. CHECK WIRE HARNESS (SHORT TO B+)

  1. C145342E01
    Turn the ignition switch off.

  1. Disconnect the negative(-) terminal cable from the battery, and wait for at least 90 seconds.

  1. for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

  1. for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N3-2 (LSP+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-4 (LSP-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O24-2 (RSP+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O24-4 (RSP-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK (for 2GR-FE)
    A
    OK (for 2AZ-FE)
    B
    NG (for LHD)
    C
    NG (for RHD)
    D



B
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)

C
REPAIR OR REPLACE FLOOR WIRE

D
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)

14. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C145342E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. for LHD:Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

  1. for RHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N3-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    N3-4 (LSP-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O24-2 (RSP+) - Body ground
    Always
    1 MΩ or higher
    O24-4 (RSP-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK (for 2GR-FE)
    A
    OK (for 2AZ-FE)
    B
    NG (for LHD)
    C
    NG (for RHD)
    D



B
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)

C
REPAIR OR REPLACE FLOOR WIRE

D
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (Oct 2006 – May 2009)B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Jun 2006 – Sep 2006) →