2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C135710
    Install the park/neutral position switch to the manual valve shaft.

  1. Temporarily install the 2 bolts.

  1. C135709
    Place a new lock plate and tighten the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the control shaft lever.

  1. C135711
    Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.

  1. Remove the control shaft lever.

  1. C099456E01
    Align the groove with the neutral basic line.

  1. Hold the switch in position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C135708
    Using a screwdriver, stake the nut with the lock plate.

  1. C135707
    Install the control shaft lever, washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. C135706
    Connect the park/neutral position switch connector.


2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C135705
    Connect the transmission control cable to the bracket with a new clip.

  1. C135109
    Connect the transmission control cable assembly to the control shaft lever with the nut.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }


3. INSTALL BATTERY
  1. Install the battery and battery tray.

  1. A134906
    Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    Nut:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.9 N*m{ 70 kgf*cm , 61 in.*lbf }


5. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P to the R position with the ignition switch to the ON position and brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position.
    If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


6. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to the N position.

  1. C135109
    Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.

  1. C135711
    Push the control shaft lever fully downward.

  1. Return the control shaft lever 2 notches to the N position.

  1. C135734E02
    Move the slider in the direction indicated by arrow A and pull up the lock piece in the direction indicated by arrow B.

    NOTICE:
    Do not damage the boot.

  1. C135109
    Install the transmission control cable to the control shaft lever with the nut.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. If the control cable end is excessively pushed up, the shift lever cannot be adjusted.
    2. When tightening the nut, confirm that the control cable is properly stretched.

  1. C138300E01
    Push in the lock piece.

    NOTICE:
    Firmly push in the lock piece until the slider lock is engaged.

    HINT:
    After pushing the lock piece make sure that the boot is not deformed.

  1. Start the engine and make sure that the vehicle moves forward when moving the shift lever from the N to the D position and moves rearward when moving it to the R position.
    If it becomes hard to move the shift lever, readjust the shift lever position.


7. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:
Click here.

← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →