2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL TRANSAXLE CASE UPPER COVER

  1. C088136
    Install the transaxle case upper cover with the 3 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }


2. INSTALL ENGINE MOUNTING FRONT BRACKET

  1. D025420
    Install the engine mounting front bracket to the automatic transaxle with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


3. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
  1. Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. C088135
    Install the oil filler tube to the automatic transaxle with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Install the ATF level gauge.


4. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

  1. C088278
    Install the No. 1 transmission control cable bracket with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


5. INSTALL NO. 1 OIL COOLER INLET TUBE
  1. Temporarily install the No. 1 oil cooler outlet tube.

  1. Temporarily install the No. 1 oil cooler inlet tube.

  1. C091745
    Install the oil cooler tube clamp with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 48 in.*lbf }

    HINT:
    Install the oil cooler tube clamp so that the oil cooler tube cushions are positioned as shown in the illustration.

  1. C092540E02
    Using SST and a wrench, tighten the No. 1 oil cooler inlet tube.
    SST
    09023-12701  

    Torque:
    For use without SST:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }
    For use with SST:
    32 N*m{ 322 kgf*cm , 24 ft.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 345 mm (13.58 in.).


6. INSTALL NO. 1 OIL COOLER OUTLET TUBE
  1. Using SST and a wrench, tighten the No. 1 oil cooler outlet tube.

    SST
    09023-12701  

    Torque:
    For use without SST:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }
    For use with SST:
    32 N*m{ 322 kgf*cm , 24 ft.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 345 mm (13.58 in.).


7. CONNECT CONNECTORS

  1. D030864E09
    Connect the transmission wire connector.

  1. Connect the park/neutral position switch connector.

  1. Connect the 2 speed sensor connectors.


8. CONNECT WIRE HARNESS

  1. C092393E03
    Connect the wire harness with the bolt.

    Torque:
    12 N*m{ 130 kgf*cm , 9 ft.*lbf }


9. INSTALL WIRE HARNESS CLAMP BRACKET

  1. C092392E02
    Install the 2 brackets with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the wire harnesses to the clamps.


10. INSTALL NO. 2 TRANSMISSION CONTROL CABLE BRACKET

  1. C092394E03
    Install the No. 2 transmission control cable bracket with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


11. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Coat a new O-ring with ATF, and install it to the hole cover.

  1. C135002
    Install the hole cover to the transaxle case with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 47 in.*lbf }


12. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY

  1. C205325
    Engage the splines of the input shaft and turbine runner.

  1. C205326
    Engage the splines of the stator shaft and stator while turning the torque converter clutch assembly.

    HINT:
    If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm and engage the splines while rotating the torque converter clutch assembly.

  1. C205327
    Turn the torque converter clutch assembly to engage the key of the oil pump drive gear into the slot on the torque converter clutch assembly.

  1. C202919E01
    Using a vernier caliper and a straightedge, measure dimension "A" between the transaxle contact surfaces of the engine *1 and the converter contact surfaces of the drive plate *2. (#)

    NOTICE:
    Make sure to deduct the thickness of the straightedge.

  1. C205295E01
    Using a vernier caliper and a straightedge, measure dimension "B" shown in the illustration and check that "B" is greater than "A", which was measured in step (#).

    Standard:
    A + 1 mm (0.0394 in.) or more

    NOTICE:
    1. Make sure to deduct the thickness of the straightedge.
    2. If the transaxle is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.


13. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

  1. C205328E01
    Apply clutch spline grease to the circumference of the crankshaft contact surface with the torque converter centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent

    Maximum spread:
    About 1 g (0.0353 oz.)

  1. C193868E03
    Install the automatic transaxle to the engine with the 5 bolts.

    Torque:
    Bolt A:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }
    Bolt B:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }
    Bolt C:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }

    NOTICE:
    Confirm that the 2 knock pins are on the transaxle fitted surface of the engine block before the transaxle installation.

  1. C127820E01
    Install the 4 lower side mounting bolts.

    Torque:
    Bolt D:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


14. INSTALL STARTER ASSEMBLY

  1. A134877
    Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 380 kgf*cm , 28 ft.*lbf }

  1. A134876
    Connect the wire harness to terminal 30 and install the nut. Then, attach the terminal cap.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the terminal 50 connector to the starter assembly.


15. INSTALL ENGINE WIRE

16. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

  1. C083851E03
    Coat the spline of the inboard joint shaft assembly with ATF.

  1. Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.

    NOTICE:
    1. Set the shaft snap ring with the opening side facing down.
    2. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    3. Move the drive shaft assembly while keeping it level.


17. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

  1. C080304E04
    Coat the spline of the inboard joint shaft assembly with ATF.

  1. Install the front drive shaft assembly RH.

  1. Using a screwdriver, install a new bearing bracket hole snap ring.

    NOTICE:
    1. Do not damage the boot and oil seal.
    2. Move the drive shaft assembly while keeping it level.

  1. Install a new bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }


18. INSTALL FRONT FRAME ASSEMBLY

  1. A052490
    For automatic transaxle:
    Install the engine mounting insulator LH with the nut.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

  1. A059881
    For manual transaxle:
    Install the engine mounting insulator LH with the bolt.

    Torque:
    143 N*m{ 1,459 kgf*cm , 105 ft.*lbf }

  1. A052482
    Install the engine mounting insulator RH with the nut.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

  1. A059880
    Install the engine mounting insulator FR with the bolt.

    Torque:
    87 N*m{ 888 kgf*cm , 64 ft.*lbf }

  1. A060825
    For manual transaxle:
    Install the engine lateral control rod with the bolt.

    Torque:
    89 N*m{ 910 kgf*cm , 66 ft.*lbf }


19. INSTALL VANE PUMP ASSEMBLY

  1. A059879
    Install the vane pump to the engine with the 2 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }

  1. Connect the oil pressure switch connector.


20. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

  1. A059877E02
    Set the engine assembly with transaxle on the engine lifter.

  1. Install the engine assembly to the vehicle.

  1. Install the frame side plate LH and RH with the 4 bolts and 2 nuts.

    Torque:
    Bolt A:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    Bolt B and nut:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. A059878E02
    Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.

    Torque:
    Bolt C:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    Bolt D and nut:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


21. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C132549E01
    Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. C132548E02
    Install the bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. C133172
    Install the clamp to the steering column hole shield.


22. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

  1. A057108E02
    Apply a few drops of adhesive to 2 threads of the 6 torque converter clutch mounting bolt tips.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. C092290
    Turn the crankshaft to gain access to each bolt and install the 6 torque converter setting bolts while holding the crankshaft pulley bolt with a wrench.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }

    NOTICE:
    First install the black colored bolt, and then the silver colored 5 bolts.

  1. C094159
    Install the flywheel housing under cover.


23. INSTALL FRONT AXLE ASSEMBLY LH

  1. F047689E03
    Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.


24. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure as described for the LH side.


25. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM LH

  1. F040142E03
    Install the lower ball joint to the front suspension lower No. 1 arm with the bolt and 2 nuts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }


26. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedure as described for the LH side.


27. INSTALL TIE ROD ASSEMBLY LH
  1. Install the tie rod end sub-assembly to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut up to 60° further.


28. INSTALL TIE ROD ASSEMBLY RH

HINT:
Use the same procedure as described for the LH side.


29. INSTALL FRONT SPEED SENSOR LH

  1. C132782E01
    Install the front speed sensor to the steering knuckle with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.

  1. C140592
    Install the flexible hose and the speed sensor to the shock absorber with the bolt and set the sensor clip on the knuckle.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.


30. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedure as described for the LH side.


31. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

  1. C140591
    Install the stabilizer link assembly with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


32. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure as described for the LH side.


33. INSTALL FRONT AXLE HUB NUT LH

  1. C068609E02
    Using a socket wrench (30 mm), install a new axle hub nut.

    Torque:
    294 N*m{ 3,000 kgf*cm , 217 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle hub nut.


34. INSTALL FRONT AXLE HUB NUT RH

HINT:
Use the same procedure as described for the LH side.


35. INSTALL FRONT EXHAUST PIPE ASSEMBLY

HINT:
Click here.


36. CONNECT COMPRESSOR AND PULLEY

  1. A134944E01
    Install the compressor with the 4 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the compressor.


37. INSTALL GENERATOR ASSEMBLY

  1. A097394E03
    Confirm that the wire harness of the crankshaft position sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.

  1. A142104E01
    Install the generator assembly with the 2 bolts.

    Torque:
    Bolt A:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }
    Bolt B:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. A135170
    Install the generator wire to terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the clamp bracket with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Attach the clamp and connect the generator connector to the generator.


38. CONNECT FUEL TUBE SUB-ASSEMBLY

  1. B012944
    Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.

    NOTICE:
    1. Check for damage or contamination on the connected part of the pipe.
    2. Check if the pipe and the connector are securely connected by trying to pull them apart.

  1. A129626
    Install the No. 1 fuel pipe clamp.


39. CONNECT RETURN TUBE SUB-ASSEMBLY

  1. A060073
    Connect the return tube sub-assembly.


40. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

  1. A060072
    Connect the No. 1 oil reservoir to pump hose.


41. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C090579
    Connect the transmission control cable assembly to the control cable clamp.

  1. C135705
    Connect the transmission control cable to the bracket with a new clip.

  1. C135109
    Connect the transmission control cable assembly to the control shaft lever with the nut.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }


42. CONNECT ENGINE WIRE

  1. A134914E01
    Install the 2 bolts and clamp to the body.

    Torque:
    Bolt A:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }
    Bolt B:
    12 N*m{ 123 kgf*cm , 9 ft.*lbf }

  1. A134913
    Connect the clamp to the bracket.

  1. A132975
    Connect the wire to the engine room junction block. Then, install it with the nut and 3 connectors.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }


43. INSTALL ECM

HINT:
Click here.


44. CONNECT HEATER WATER HOSE INLET

  1. A124832
    Connect the heater inlet water hose.


45. CONNECT HEATER WATER HOSE OUTLET

  1. A124831
    Connect the heater outlet water hose.


46. CONNECT OIL COOLER INLET HOSE

  1. A128128
    Connect the oil cooler inlet hose to the radiator assembly.


47. CONNECT OIL COOLER OUTLET HOSE

  1. A128129
    Connect the oil cooler outlet hose to the radiator assembly.


48. CONNECT RADIATOR HOSE INLET

  1. A134907
    Install the clamp and connect the radiator hose inlet.


49. CONNECT RADIATOR HOSE OUTLET

  1. A127545
    Install the clamp and connect the radiator hose outlet.


50. CONNECT NO. 1 VACUUM HOSE CONNECTOR

  1. A134908
    Install the clamp and connect the No. 1 vacuum hose connector.


51. INSTALL NO. 2 ENGINE MOUNTING BRACKET RH

  1. A134911
    Install the No. 2 engine mounting bracket RH with the 3 bolts.

    Torque:
    52 N*m{ 531 kgf*cm , 38 ft.*lbf }


52. INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

  1. A134910
    Install the engine moving control rod with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. A134909
    Install the ground cable with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }


53. INSTALL NO. 2 ENGINE MOUNTING STAY RH

  1. A134912
    Install the No. 2 engine mounting stay RH with the 2 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


54. INSTALL BATTERY
  1. Install the battery and battery tray.

  1. A134906
    Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    Nut:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


55. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A134905
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose clamp.


56. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


57. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A134903
    Install the air cleaner inlet with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


58. INSTALL V-RIBBED BELT

  1. A114351E03
    Using SST and a 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then install the V-ribbed belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply more force than necessary.

  1. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Check to confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.


59. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY

  1. C141972E01
    Install the outer cowl top panel sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }


60. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Click here.


61. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


62. ADD ENGINE OIL

63. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.9 N*m{ 70 kgf*cm , 61 in.*lbf }


64. ADD ENGINE COOLANT
  1. Close the radiator drain cock plug and cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    6.7 liters (7.1 US qts, 5.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


65. ADD AUTOMATIC TRANSAXLE FLUID

Fluid type:
Toyota Genuine ATF WS


66. ADD POWER STEERING FLUID

67. BLEED POWER STEERING FLUID
  1. Check the fluid level (Click here).

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the steering wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the steering wheel to the left or right to the full lock position and keep it in that position for 2 to 3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds.

    2. Repeat this procedure several times.

  1. Stop the engine.

  1. C137876E01
    Check for foaming or emulsification.

    HINT:
    If the system has to be bled twice because of forming or emulsification, be sure to check for fluid leaks in the system.

  1. Check the fluid level (Click here).


68. INSPECT AUTOMATIC TRANSAXLE FLUID

HINT:
Drive the vehicle so that the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80°C (158 to 176°F)

  1. D025120E03
    Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to L. Then return it to P.

  1. Pull out the dipstick and wipe it clean.

  1. Push it back fully into the pipe.

  1. Pull it out again and check that the fluid level is within the HOT range. If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add proper amount of new fluid and recheck the fluid level.


69. INSPECT FOR FUEL LEAK

HINT:
Click here.


70. INSPECT FOR ENGINE OIL LEAK

71. INSPECT FOR ENGINE COOLANT LEAK

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A135234
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


72. INSPECT FOR EXHAUST GAS LEAK

73. CHECK SHIFT LEVER POSITION
  1. When shifting from the P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into the position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position. If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


74. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to the N position.

  1. C135109
    Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.

  1. C135711
    Push the control shaft fully downward.

  1. Return the control shaft lever 2 notches to the N position.

  1. C135734E02
    Move the slider in the directions indicated by arrow A and pull up the lock piece in the direction indicated by arrow B.

    NOTICE:
    Do not damage the boot.

  1. C135109
    Connect the transmission control cable assembly to the control shaft lever with the nut.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not damage the boot.

  1. C138300E01
    Push in the lock piece.

    NOTICE:
    Firmly push in the lock piece until the slider lock is engaged.

  1. Start the engine and make sure that the vehicle moves forward when moving the lever from the N to the D position and moves rearward when moving it to the R position.
    If it becomes hard to move the shift lever, readjust the shift lever position.


75. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
Click here.


76. CHECK IGNITION TIMING
  1. Warm up the engine.

  1. C139987E06
    When using the intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

    2. Enter DATA LIST MODE on the intelligent tester.

      Ignition timing:
      8 to 12° BTDC at idle

      HINT:
      Refer to the intelligent tester operator's manual for help when selecting the DATA LIST.

  1. A082779E69
    When not using the intelligent tester:
    Check the ignition timing.

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the electrical system.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor has turned off.

    2. A052004
      Remove the No. 1 engine cover.

    3. Pull out the wire harness as shown in the illustration. Connect the clip of the timing light to the wire harness.

      NOTICE:
      1. Use a timing light which can detect the first signal.
      2. After checking, be sure to tape the wire harness.

    4. Check the ignition timing at idle.

      Ignition timing:
      8 to 12° BTDC at idle

      NOTICE:
      When checking the ignition timing, the transmission should be in neutral.

      HINT:
      After the engine rpm is kept at 1,000 to 1,300 rpm for 5 seconds, check that it returns to idle speed.

    5. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    6. Check the ignition timing at idle.

      Ignition timing:
      5 to 15° BTDC at idle

    7. Confirm that the ignition timing moves to the advanced angle side when the engine rpm is increased.

    8. Remove the timing light.

    9. Install the No. 1 engine cover.


77. CHECK ENGINE IDLE SPEED

  1. C139987E06
    Warm up the engine.

  1. When using the intelligent tester:
    Check the idle speed.

    1. Connect the intelligent tester to the DLC3.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    2. Enter DATA LIST MODE on the intelligent tester.

      Idle speed:
      Item
      Specified Condition
      Manual transmission
      850 to 950 rpm
      Automatic transmission
      610 to 710 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be in neutral.
      2. Check the idle speed with the cooling fan off.
      3. Switch off all accessories and air conditioning before connecting the intelligent tester.

  1. A082779E70
    When not using the intelligent tester:
    Check the idle speed.

    1. Using SST, connect the tachometer tester probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Check the idle speed.

      Idle speed:
      Item
      Specified Condition
      Manual transmission
      850 to 950 rpm
      Automatic transmission
      610 to 710 rpm


78. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/at 2,500 rpm.

    HINT:
    1. Complete the measurement within 3 minutes.
    2. Check regulations and restrictions in your area when performing 2 mode CO/HC concentration testing (engine check at both idle speed and at 2,500 rpm).

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check A/F sensor operation (Click here).

    2. Check heated oxygen sensor operation (Click here).

    3. See the table below for possible causes, and then inspect and repair.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted, or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaking intake or exhaust valves
      4. Compression leaks from cylinders
      Low
      High
      Rough idle
      (fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Defective MAF meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor


79. INSTALL FRONT FENDER APRON SEAL RH

80. INSTALL ENGINE UNDER COVER LH

81. INSTALL ENGINE UNDER COVER RH

82. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Install the engine cover with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


83. CHECK ABS SPEED SENSOR SIGNAL

HINT:
Click here.

← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (from Jun 2006) →