2006-2011 Camry Aurion · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

4. REMOVE FRONT WHEELS

5. REMOVE ENGINE UNDER COVER LH

6. REMOVE ENGINE UNDER COVER RH

7. REMOVE FRONT FENDER APRON SEAL RH

8. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.


9. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

  1. Loosen the radiator drain cock plug and cylinder block drain cock plug, then drain the coolant.

    A136224E04

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


10. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Using a 6 mm socket hexagon wrench, remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 499 kgf*cm , 36 ft.*lbf }


11. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Click here.


12. REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY

  1. C141972E01
    Remove the 4 bolts, 4 nuts and outer cowl top panel sub-assembly.


13. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Remove the 2 nuts and cover.


14. REMOVE V-RIBBED BELT

  1. A114351E03
    Using SST and a 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then remove the V-ribbed belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply more force than necessary.


15. REMOVE AIR CLEANER INLET ASSEMBLY

  1. A134903
    Remove the 2 bolts, clamp and air cleaner inlet.


16. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A144946E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).

  1. A146036
    Disconnect the No. 2 ventilation hose from the air cleaner hose.

  1. A135668
    Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.

  1. A146037
    Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


17. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A134905
    Disconnect the hose clamp.

  1. Remove the 3 bolts and air cleaner case.


18. REMOVE BATTERY

  1. A134906
    Loosen the bolt and nut, and remove the battery clamp.

  1. Remove the battery and battery tray.


19. REMOVE NO. 2 ENGINE MOUNTING STAY RH

  1. A134912
    Remove the 2 bolts and No. 2 engine mounting stay RH.


20. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

  1. A134909
    Remove the bolt and disconnect the ground cable.

  1. A134910
    Remove the 3 bolts and the engine moving control rod sub-assembly.


21. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH

  1. A134911
    Remove the 3 bolts and No. 2 engine mounting bracket RH.


22. DISCONNECT NO. 1 VACUUM HOSE CONNECTOR

  1. A134908
    Remove the clamp and disconnect the No. 1 vacuum hose connector.


23. DISCONNECT RADIATOR HOSE INLET

  1. A134907
    Remove the clamp and disconnect the No. 1 radiator hose.


24. DISCONNECT RADIATOR HOSE OUTLET

  1. A127545
    Remove the clamp and disconnect the No. 2 radiator hose.


25. DISCONNECT OIL COOLER INLET HOSE

  1. A133365
    Disconnect the oil cooler inlet hose from the radiator assembly.


26. DISCONNECT OIL COOLER OUTLET HOSE

  1. A133366
    Disconnect the oil cooler outlet hose from the radiator assembly.


27. DISCONNECT HEATER WATER HOSE INLET

  1. A124832
    Disconnect the heater inlet water hose.


28. DISCONNECT HEATER WATER HOSE OUTLET

  1. A124831
    Disconnect the heater outlet water hose.


29. REMOVE ECM

HINT:
Click here.


30. DISCONNECT ENGINE WIRE

  1. A132975
    Disconnect the engine wire from the engine room relay block.

    1. Remove the nut and separate the wire harness.

    2. Using a screwdriver, unlock the engine room R/B. Pull the engine room R/B upward.

    3. Disconnect the engine wire connectors.

  1. A134913
    Remove the clamp from the bracket.

  1. A134914
    Remove the 2 bolts and clamp from the body.


31. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C135109
    Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.

  1. C135705
    Remove the clip and disconnect the transmission control cable assembly from the No. 1 control cable bracket.

  1. C090579
    Disconnect the transmission control cable assembly from the control cable clamp.


32. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

  1. A060072
    Disconnect the No. 1 oil reservoir to pump hose.


33. DISCONNECT RETURN TUBE SUB-ASSEMBLY

  1. A060073
    Disconnect the return tube sub-assembly.


34. DISCONNECT FUEL TUBE SUB-ASSEMBLY

  1. A129626
    Remove the No. 1 fuel pipe clamp.

  1. B012941E15
    Disconnect the connector from the tube while pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for contamination in the tube and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.


35. REMOVE GENERATOR ASSEMBLY

  1. A135170
    Disconnect the generator connector.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and wire harness clamp bracket.

  1. Remove the wire harness clamp.

  1. A142104
    Remove the 2 bolts and generator assembly.


36. SEPARATE COMPRESSOR AND PULLEY

  1. A134944
    Disconnect the connector.

  1. Remove the 4 bolts and separate the compressor.

    HINT:
    Hang up the hoses instead of detaching them.


37. REMOVE FRONT EXHAUST PIPE ASSEMBLY

HINT:
Click here.


38. REMOVE FRONT AXLE HUB NUT LH

  1. C108168E02
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


39. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures as described for the LH side.


40. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

  1. C140591
    Remove the nut and separate the front stabilizer link assembly.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


41. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


42. SEPARATE FRONT SPEED SENSOR LH

  1. C140592
    Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.

  1. C132782E01
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.


43. SEPARATE FRONT SPEED SENSOR RH

HINT:
Use the same procedures as described for the LH side.


44. SEPARATE TIE ROD ASSEMBLY LH

  1. C108515E05
    Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end sub-assembly from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Make sure that the string of SST is securely tied to the vehicle.
    2. Be careful not to damage the ball joint dust cover.
    3. Be careful not to damage the steering knuckle.
    4. Be careful not to damage the front disc brake dust cover.


45. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


46. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM LH

  1. F040142E01
    Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.


47. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures as described for the LH side.


48. SEPARATE FRONT AXLE ASSEMBLY LH

  1. D032030E06
    Put matchmarks on the front drive shaft assembly and the axle hub.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.


49. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


50. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

  1. C092289
    Remove the flywheel housing under cover.

  1. C092290
    Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.

    HINT:
    There will be one black colored bolt.


51. SEPARATE STEERING SLIDING YOKE

  1. C133501
    Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.

  1. C156702E01
    Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.

  1. C156703E01
    Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.


52. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

  1. A059877
    Set the engine lifter.

  1. Remove the 4 bolts, 2 nuts and frame side rail plate RH and LH.

  1. A059878
    Remove the 4 bolts, 2 nuts and front suspension member brace rear RH and LH.

  1. Carefully remove the engine assembly from the vehicle.

  1. A090847E03
    Install the 2 engine hangers as shown in the illustration.
    Part No.:
    Parts
    Part No.
    No. 1 engine hanger
    12281-28010
    No. 2 engine hanger
    12282-28010
    Bolt
    91512-61020

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Using a chain block and an engine sling device, hang the engine assembly.


53. REMOVE VANE PUMP ASSEMBLY

  1. A059879
    Disconnect the oil pressure switch connector.

  1. Loosen the 2 bolts and remove the vane pump from the engine.


54. REMOVE FRONT FRAME ASSEMBLY

  1. A052490
    For automatic transaxle:
    Remove the nut from the engine mounting insulator LH.

  1. A059881
    For manual transaxle:
    Remove the bolt from the engine mounting insulator LH.

  1. A052482
    Remove the nut from the engine mounting insulator RH.

  1. A059880
    Remove the bolt from the engine mounting insulator FR.

  1. A060825
    For manual transaxle:
    Remove the bolt from the engine lateral control rod.

  1. Raise the engine assembly and separate the front frame.


55. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

  1. C083850E02
    Using SST, remove the front drive shaft assembly LH.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    2. Be careful not to drop the drive shaft assembly.


56. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

  1. C080304E03
    Using a screwdriver, remove the bearing bracket hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot and oil seal.


57. REMOVE ENGINE WIRE

58. REMOVE STARTER ASSEMBLY

  1. A134876
    Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. A134877
    Remove the 2 bolts and starter assembly.


59. REMOVE ENGINE MOUNTING FRONT BRACKET

  1. D025420
    Remove the 3 bolts and engine mounting front bracket.


60. SEPARATE AUTOMATIC TRANSAXLE ASSEMBLY

  1. C127822
    Remove the 5 bolts.

  1. C127820
    Remove the 4 lower side mounting bolts.

  1. Separate and remove the automatic transaxle.


61. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

62. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

  1. C135002
    Remove the bolt and hole cover from the transaxle case.

  1. Remove the O-ring from the hole cover.


63. REMOVE NO. 2 TRANSMISSION CONTROL CABLE BRACKET

  1. C092391E01
    Remove the bolt and No. 2 transmission control cable bracket.


64. REMOVE WIRE HARNESS CLAMP BRACKET

  1. C092392E02
    Disconnect the wire harnesses from the 2 clamps.

  1. Remove the 2 bolts and 2 brackets.


65. DISCONNECT WIRE HARNESS

  1. C092393E03
    Remove the bolt and disconnect the wire harness.


66. DISCONNECT CONNECTORS

  1. D030864E09
    Disconnect the transmission wire connector.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the 2 speed sensor connectors.


67. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

  1. C091736
    Remove the bolt and oil cooler tube clamp.

  1. Remove the 2 bolts and No. 1 transmission control cable bracket.


68. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
  1. Remove the ATF level gauge.

  1. C091737E02
    Remove the bolt and transmission oil filler tube sub-assembly.

  1. Remove the O-ring from the oil filler tube sub-assembly.


69. REMOVE NO. 1 OIL COOLER INLET TUBE

  1. C088047E01
    Using SST and a wrench, disconnect the No. 1 oil cooler inlet tube.
    SST
    09023-12701  


70. REMOVE NO. 1 OIL COOLER OUTLET TUBE
  1. Using SST and a wrench, disconnect the No. 1 oil cooler outlet tube.

    SST
    09023-12701  


71. REMOVE TRANSAXLE CASE UPPER COVER

  1. C088136
    Remove the 3 bolts and transaxle case upper cover.

← REMOVAL (Jun 2006 – Sep 2006)REMOVAL (from Jun 2009) →