2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL CLUTCH ACCUMULATOR ASSEMBLY

  1. C132977
    Install the clutch accumulator assembly with the 2 nuts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }


2. CONNECT CLUTCH LINE

  1. C132976E01
    Using SST, connect the clutch lines to the clutch accumulator assembly.
    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }


3. INSTALL RELEASE CYLINDER HEAT INSULATOR

  1. C132975
    Install the release cylinder heat insulator with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }


4. INSTALL CLUTCH ACCUMULATOR BRACKET

  1. C132974E01
    Install the clutch accumulator bracket with the 2 bolts.

    Torque:
    Bolt A:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }
    Bolt B:
    37 N*m{ 380 kgf*cm , 28 ft.*lbf }


5. BLEED CLUTCH PIPE LINE
  1. Fill the brake reservoir with brake fluid and bleed the clutch system.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


6. INSPECT BRAKE FLUID LEAKAGE

HINT:
Check for leakage in the clutch system.


7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A134905
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose clamp.


8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


9. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A134903
    Install the air cleaner inlet with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


10. INSPECT BRAKE FLUID LEVEL IN RESERVOIR

  1. C144901E01
    Check the fluid level.
    If brake fluid level is low, check for leakage and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair and replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← REMOVAL (from Jun 2009)INSTALLATION (Oct 2006 – May 2009) →