2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Driver Side Door Key Lock and Unlock Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The driver's door key lock and unlock switch is built into the driver's door lock assembly.
When the driver's door key cylinder is turned to lock all the doors by the key, there is continuity between terminals L and E of the key lock and unlock switch. When the cylinder is turned to unlock the door(s), there is continuity between terminals UL and E.
Terminals L2 and UL2 of the main body ECU (instrument panel J/B) are connected to the door lock assembly, and door lock/unlock request signals (by key) are input to the main body ECU (instrument panel J/B).
The main body ECU (instrument panel J/B) constantly applies voltage to terminal L of the driver's door lock assembly via terminal L2. When the driver's door key cylinder is turned to lock all the doors by the key, current flows from terminal L2 to terminal L.
The main body ECU (instrument panel J/B) also applies constant voltage to terminal UL of the door lock assembly via terminal UL2. When the door key cylinder is turned in the direction to unlock the door(s) by the key, current flows from terminal UL2 to terminal UL.

WIRING DIAGRAM

B150923E01

INSPECTION PROCEDURE


1. READ VALUE ON INTELLIGENT TESTER

  1. Connect the intelligent tester to the DLC3.B150920E01

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select Door Key SW-Lock and Door Key SW-Unlock in the DATA LIST, and read the tester display.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door lock/unlock switch lock signal (key-linked lock switch)
    /ON or OFF
    ON: Driver side door key cylinder is turned to LOCK
    OFF: Driver side door key cylinder is not turned to LOCK
    -
    Door Key SW-Unlock
    Driver door lock/unlock switch unlock signal (key-linked unlock switch)
    /ON or OFF
    ON: Driver side door key cylinder is turned to UNLOCK
    OFF: Driver side door key cylinder is not turned to UNLOCK
    -

    OK:
    The display is as specified in the "Normal Condition" column.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR KEY LOCK AND UNLOCK SWITCH)

  1. for LHD:

    1. B065428E16
      Remove the front door lock assembly LH (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      7 - 9
      ON (Door lock set to LOCK)
      Below 1 Ω
      7 - 9
      7 - 10
      OFF (Free)
      10 kΩ or higher
      7 - 10
      ON (Door lock set to UNLOCK)
      Below 1 Ω

  1. for RHD:

    1. B112613E07
      Remove the front door lock assembly RH (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      8 - 6
      ON (Door lock set to LOCK)
      Below 1 Ω
      8 - 6
      8 - 5
      OFF (Free)
      10 kΩ or higher
      8 - 5
      ON (Door lock set to UNLOCK)
      Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the instrument panel J/B connector.

B150922E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    I7-9 (L) - IK-16
    Always
    Below 1 Ω
    I7-10 (UL) - E7-10 (UL3)
    Always
    Below 1 Ω
    I7-7 (E) - Body ground
    Always
    Below 1 Ω
    I7-9 (L) - Body ground
    Always
    10 kΩ or higher
    I7-10 (UL) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    H8-6 (L) - IJ-5
    Always
    Below 1 Ω
    H8-5 (UL) - E7-10 (UL3)
    Always
    Below 1 Ω
    H8-8 (E) - Body ground
    Always
    Below 1 Ω
    H8-6 (L) - Body ground
    Always
    10 kΩ or higher
    H8-5 (UL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL J/B)


← Driver Side Door Key Lock and Unlock Switch Circuit (Oct 2006 – May 2009)Door Control Switch Circuit (Oct 2006 – May 2009) →