2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL FRONT LOWER BALL JOINT

  1. C145242
    Install the front lower ball joint to the steering knuckle with the nut.

    Torque:
    123 N*m{ 1,250 kgf*cm , 91 ft.*lbf }

    NOTICE:
    Prevent oil from adhering to the screw and tapered parts.

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.


2. INSTALL FRONT DISC BRAKE DUST COVER

  1. C145241
    Install the front disc brake dust cover to the steering knuckle with the 4 bolts.

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }


3. INSTALL FRONT AXLE ASSEMBLY

  1. C129153E01
    Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.

  1. C132414
    Install the steering knuckle with the front axle assembly to the front shock absorber with the 2 bolts and 2 nuts.

    Torque:
    210 N*m{ 2,140 kgf*cm , 155 ft.*lbf }

    NOTICE:
    1. Only when reusing the bolts and nuts, apply a small amount of engine oil to the threads of the nuts.
    2. Be careful not to damage the drive shaft boot and speed sensor rotor.


4. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM

  1. F040142E03
    Install the lower ball joint to the front suspension lower No. 1 arm with the bolt and 2 nuts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }


5. CONNECT TIE ROD END ASSEMBLY
  1. Install the tie rod end sub-assembly to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut up to 60° further.


6. INSTALL FRONT DISC

  1. C132801E01
    Align the matchmarks and install the front disc.

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has the minimum runout.


7. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

  1. C067088E05
    Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1,090 kgf*cm , 79 ft.*lbf }

    NOTICE:
    Do not twist the brake hose when installing the front disc brake caliper assembly.


8. INSTALL FRONT SPEED SENSOR

  1. C132782E01
    Install the front speed sensor to the steering knuckle with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.

  1. C140592
    Install the flexible hose and the speed sensor to the shock absorber with the bolt and set the sensor clip on the knuckle.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.


9. INSTALL FRONT AXLE HUB NUT

  1. C068609E02
    Using a socket wrench (30 mm), install a new axle hub nut.

    Torque:
    294 N*m{ 3,000 kgf*cm , 217 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle hub nut.


10. CHECK ABS SPEED SENSOR SIGNAL

HINT:
  1. ABS: Click here.
  2. VSC: Click here.


11. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


12. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)
← INSPECTION (from Jun 2006)INSTALLATION (Oct 2006 – May 2009) →