INSTALLATION
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL FRONT LOWER BALL JOINT |
 |
- Install the front lower ball joint to the steering knuckle with the nut.
-
Torque:
- 123 N*m{
1,250 kgf*cm
, 91 ft.*lbf
}
- NOTICE:
- Prevent oil from adhering to the screw and tapered parts.
Install a new cotter pin.
- NOTICE:
- If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.
| 2.
INSTALL FRONT DISC BRAKE DUST COVER |
 |
- Install the front disc brake dust cover to the steering knuckle with the 4 bolts.
-
Torque:
- 8.3 N*m{
85 kgf*cm
, 74 in.*lbf
}
| 3.
INSTALL FRONT AXLE ASSEMBLY
|
 |
- Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
- Install the steering knuckle with the front axle assembly to the front shock absorber with the 2 bolts and 2 nuts.
-
Torque:
- 210 N*m{
2,140 kgf*cm
, 155 ft.*lbf
}
- NOTICE:
- Only when reusing the bolts and nuts, apply a small amount of engine oil to the threads of the nuts.
- Be careful not to damage the drive shaft boot and speed sensor rotor.
| 4.
INSTALL FRONT SUSPENSION LOWER NO. 1 ARM
|
 |
- Install the lower ball joint to the front suspension lower No. 1 arm with the bolt and 2 nuts.
-
Torque:
- 75 N*m{
765 kgf*cm
, 55 ft.*lbf
}
| 5.
CONNECT TIE ROD END ASSEMBLY
|
 |
Install the tie rod end sub-assembly to the steering knuckle with the nut.
-
Torque:
- 49 N*m{
500 kgf*cm
, 36 ft.*lbf
}
Install a new cotter pin.
- NOTICE:
- If the holes for the cotter pin are not aligned, tighten the nut up to 60° further.
| 6.
INSTALL FRONT DISC
|
 |
- Align the matchmarks and install the front disc.
- NOTICE:
- When replacing the disc with a new one, select the installation position where the front disc has the minimum runout.
| 7.
INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
|
 |
- Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.
-
Torque:
- 107 N*m{
1,090 kgf*cm
, 79 ft.*lbf
}
- NOTICE:
- Do not twist the brake hose when installing the front disc brake caliper assembly.
| 8.
INSTALL FRONT SPEED SENSOR
|
 |
- Install the front speed sensor to the steering knuckle with the bolt.
-
Torque:
- 8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
- NOTICE:
- Prevent foreign matter from adhering to the speed sensor.
- Be careful not to damage the speed sensor.
- Install the flexible hose and the speed sensor to the shock absorber with the bolt and set the sensor clip on the knuckle.
-
Torque:
- 19 N*m{
192 kgf*cm
, 14 ft.*lbf
}
- NOTICE:
- Be careful not to damage the speed sensor.
- Prevent foreign matter from adhering to the speed sensor.
- Do not twist the sensor wire when installing the speed sensor.
| 9.
INSTALL FRONT AXLE HUB NUT
|
 |
- Using a socket wrench (30 mm), install a new axle hub nut.
-
Torque:
- 294 N*m{
3,000 kgf*cm
, 217 ft.*lbf
}
Using a chisel and hammer, stake the front axle hub nut.
| 10.
CHECK ABS SPEED SENSOR SIGNAL |
 |
- HINT:
- ABS: Click here.
- VSC: Click here.
| 11.
INSTALL FRONT WHEEL |
 |
-
Torque:
- 103 N*m{
1,050 kgf*cm
, 76 ft.*lbf
}
| 12.
INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
 |
(Click here)