2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Oct 2006

Versions by build date: Jun 2006 – Sep 2006 from Oct 2006

NOTICE:
If an old gasket still remains on the pipe, remove it. Also, if any bolts or nuts are rusted, replace them.


1. REMOVE REAR WHEELS

2. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE)

  1. Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.

    A146049

  1. Remove the gasket from the front exhaust pipe.


3. REMOVE TAIL EXHAUST PIPE ASSEMBLY (for 2GR-FE)

  1. Remove the 4 nuts and 2 exhaust tail pipes.

    A146044

  1. Remove the 2 gaskets from the exhaust tail pipes.


4. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2GR-FE)

  1. Remove the 2 bolts, 2 nuts and exhaust center pipe assembly.

    A146045

  1. Remove the gasket from the exhaust front pipe assembly.


5. SEPARATE REAR STABILIZER LINK ASSEMBLY LH

  1. C144428E01
    Remove the nut and separate the rear stabilizer link assembly LH (lower side) from the rear stabilizer bar.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud.


6. SEPARATE REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedures as for the LH side.


7. REMOVE NO. 2 REAR STABILIZER BAR BRACKET

  1. C145565
    Remove the 2 bolts and No. 2 rear stabilizer bar bracket.


8. REMOVE NO. 1 REAR STABILIZER BAR BRACKET

  1. C145566
    Remove the 2 bolts and No. 1 rear stabilizer bar bracket.


9. REMOVE REAR STABILIZER BAR
  1. Remove the rear stabilizer bar with the stabilizer bushing.


10. DISCONNECT REAR HEIGHT CONTROL SENSOR CONNECTOR (w/ HID Headlight System)

  1. C146083
    Disconnect the rear height control sensor connector.


11. SEPARATE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (w/ HID Headlight System)

  1. C137785
    Remove the nut and separate the rear height control sensor sub-assembly RH from the rear No. 2 suspension arm RH.


12. SEPARATE REAR STRUT ROD LH

  1. C144124
    Support the rear axle carrier with a jack.

  1. Remove the bolt and nut, and separate the rear strut rod LH (rear side) from the rear axle carrier.

    NOTICE:
    When removing the bolt, keep the nut from rotating.


13. SEPARATE REAR STRUT ROD RH

HINT:
Perform the same procedures as for the LH side.


14. SEPARATE REAR NO. 2 SUSPENSION ARM LH

  1. C144132
    Remove the bolt and nut, and separate the rear No. 2 suspension arm (outer side) from the rear axle carrier.

    NOTICE:
    When removing the bolt, keep the nut from rotating.


15. SEPARATE REAR NO. 2 SUSPENSION ARM RH

HINT:
Perform the same procedures as for the LH side.


16. SEPARATE REAR NO. 1 SUSPENSION ARM LH

  1. C144131
    Remove the bolt and nut, and separate the rear No. 1 suspension arm (outer side) from the rear axle carrier.

    NOTICE:
    When removing the bolt, keep the nut from rotating.


17. SEPARATE REAR NO. 1 SUSPENSION ARM RH

HINT:
Perform the same procedures as for the LH side.


18. REMOVE REAR SUSPENSION MEMBER LOWER STOPPER LH

  1. C132500
    Remove the 2 nuts and the rear suspension member lower stopper LH.


19. REMOVE REAR SUSPENSION MEMBER LOWER STOPPER RH

  1. C138862
    Remove the 2 nuts and the rear suspension member lower stopper RH.


20. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (w/ Sport Suspension)

  1. C132502
    Support the rear suspension member with a jack.

  1. Remove the 2 bolts and the 2 rear suspension member lower stoppers.

  1. Remove the rear suspension member sub-assembly with the 4 differential support member cushions.


21. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

  1. C132502
    Support the rear suspension member with a jack.

  1. Remove the 2 bolts and the 2 rear suspension member lower stoppers.

  1. Remove the rear suspension member sub-assembly.


22. REMOVE REAR NO. 2 SUSPENSION ARM LH

  1. C141343
    Remove the bolt and the rear No. 2 suspension arm LH.

← REMOVAL (Jun 2006 – Sep 2006)INSTALLATION (Jun 2006 – Sep 2006) →