2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL REAR NO. 2 SUSPENSION ARM LH

  1. C141343E01
    Install the rear No. 2 suspension arm (inside) with the bolt, and temporarily tighten the bolt.

    HINT:
    Ensure that the paint marks face to the rear of the vehicle.


2. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY (w/ Sport Suspension)

  1. C132502
    Raise the rear suspension member sub-assembly with a jack.

  1. Install the rear suspension member sub-assembly with the 4 differential support member cushions.

  1. Install the 2 rear suspension member lower stoppers and 2 bolts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }


3. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

  1. C132502
    Raise the rear suspension member sub-assembly with a jack.

  1. Install the rear suspension member sub-assembly with the 2 rear suspension member lower stoppers and 2 bolts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }


4. INSTALL REAR SUSPENSION MEMBER LOWER STOPPER LH

  1. C132500E01
    Install the rear suspension member lower stopper LH with the 2 nuts.

    Torque:
    Nut A:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    Nut B:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }


5. INSTALL REAR SUSPENSION MEMBER LOWER STOPPER RH

  1. C138862E01
    Install the rear suspension member lower stopper RH with the 2 nuts.

    Torque:
    Nut A:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    Nut B:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }


6. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM LH

  1. C144131
    Connect the rear No. 1 suspension arm (outer side) to the rear axle carrier with the bolt and nut, and temporarily tighten the bolt and nut.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the front of the vehicle and temporarily install the bolt.


7. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM RH

HINT:
Perform the same procedures as for the LH side.


8. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM LH

  1. C144132
    Connect the rear No. 2 suspension arm (outer side) to the rear axle carrier with the bolt and nut, and temporarily tighten the bolt.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the rear of the vehicle and temporarily install the bolt.


9. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM RH

HINT:
Perform the same procedures as for the LH side.


10. TEMPORARILY TIGHTEN REAR STRUT ROD LH

  1. C144133
    Connect the rear strut rod assembly LH (rear side) to the axle carrier with the bolt and nut, and temporarily tighten the bolt.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the inside of the vehicle and temporarily install the bolt.


11. TEMPORARILY TIGHTEN REAR STRUT ROD RH

HINT:
Perform the same procedures as for the LH side.


12. STABILIZE SUSPENSION

  1. C108450E01
    Jack up the rear axle carrier, placing a wooden block to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm (inner side) is horizontally aligned with the center of the rear axle hub.


13. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM LH

  1. C144134
    Fully tighten the bolt.

    Torque:
    100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


14. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM RH

HINT:
Perform the same procedures as for the LH side.


15. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM LH

  1. C144238
    Fully tighten the 2 bolts.

    Torque:
    100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


16. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM RH

HINT:
Perform the same procedures as for the LH side.


17. FULLY TIGHTEN REAR STRUT ROD LH

  1. C132476
    Fully tighten the bolt.

    Torque:
    113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }


18. FULLY TIGHTEN REAR STRUT ROD RH

HINT:
Perform the same procedures as for the LH side.


19. INSTALL NO. 2 REAR STABILIZER BAR BRACKET
  1. Install the No. 2 rear stabilizer bar bracket.


20. INSTALL NO. 1 REAR STABILIZER BAR BRACKET
  1. Install the No. 1 rear stabilizer bar bracket.


21. INSTALL REAR STABILIZER BAR

  1. C145565
    Install the rear stabilizer bar with the 2 bolts. (LH Side)

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. C145566
    Install the rear stabilizer bar with the 2 bolts. (RH Side)

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }


22. INSTALL REAR STABILIZER LINK ASSEMBLY LH

  1. C144428E01
    Connect the rear stabilizer link assembly LH with the nut.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud.


23. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedures as for the LH side.


24. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install a new gasket onto the front exhaust pipe.

  1. Install the center exhaust pipe assembly with the 2 bolts and 2 nuts.

    A146049

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }


25. INSTALL REAR WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


26. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace the damaged parts as necessary.

27. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)
← REMOVAL (from Oct 2006)INSTALLATION (Oct 2006 – May 2009) →