Illumination Circuit
Circuit diagnosis · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).
| 1. CHECK ILLUMINATION |
Check if the illumination for the navigation receiver assembly, steering pad switch assembly, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.
- Result:
Result
Proceed to
Illumination comes on for all components except steering pad switch assembly.
A
Illumination comes on for all components except navigation receiver assembly.
B
No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.).
C
(for 2AZ-FE)
D
(for 2GR-FE)
Illumination comes on for all components except navigation receiver assembly and steering pad switch assembly.
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE) |
Disconnect the E18 spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E18-12 (IL+2) - Body ground
Light control switch in tail or head
11 to 14 V
|
|
||||
| OK | |
| 3. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the steering pad switch assembly and spiral cable sub-assembly connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
a1-8 (EAU) - E18-4 (EAU)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
a1-5 (IL+2) - E18-12 (IL+2)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
- NOTICE:
- The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.
- HINT:
- Removal (Click here)
- Installation (Click here)
- Removal (Click here)
Text in Illustration *1
Component without harness connected
(Spiral Cable Sub-assembly)
*2
Steering Pad Switch Side
*3
Vehicle Side
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY) |
Disconnect the F38 navigation receiver assembly.
Disconnect the E18 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F38-6 (SWG) - E18-4 (EAU)
Always
Below 1 Ω
E18-4 (EAU) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Connect a positive (+) lead from the battery to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.


Check if the illumination for the steering pad switch assembly comes on.
- OK:
- Illumination for the steering pad switch assembly comes on.
Text in Illustration *1
Component without harness connected
(Steering Pad Switch Assembly for 3 Spoke Type)
*2
Component without harness connected
(Steering Pad Switch Assembly for 4 Spoke Type)
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY) |
Disconnect the F36 navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
F36-10 (ILL+) - Body ground
Light control switch in tail or head
11 to 14 V
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND) |
Disconnect the F36 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F36-7 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
