2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E134726E04

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) such as the airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or others (Hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

    Result:
    Condition
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.)
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM
A


2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)

  1. E120026E20
    Disconnect the spiral cable connector E18.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E18-12 (IL+2) - Body ground
    Light control switch tail or head
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK STEERING PAD SWITCH ASSEMBLY

  1. Disconnect the steering pad switch assembly connector.E137740E01

  1. Connect the positive (+) lead to terminal ILL+ and the negative (-) lead to terminal EAU of the steering pad switch connector.

  1. Check if the illumination for the steering pad switch comes on.

OK:
Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


4. INSPECT SPIRAL CABLE

  1. I039337E58
    Disconnect the a1 steering pad switch and E18 spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Spiral cable position
    Specified Condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-5 (ILL+) - E18-12 (ILL+)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may cause airbag deployment. Be sure to read the page shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)



NG
REPLACE SPIRAL CABLE
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER ASSEMBLY)

  1. E137741E01
    Disconnect the F38 navigation receiver assembly and E18 spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F38-6 (SWG) - E18-4 (EAU)
    Always
    Below 1 Ω
    F38-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY

6. CHECK HARNESS AND CONNECTOR

  1. E137742E01
    Disconnect the navigation receiver assembly connector F36.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F36-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F36-10 (ILL+) - Body ground
    Light control switch tail or head
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Steering Pad Switch Circuit (from Jun 2009)Illumination Circuit (Oct 2006 – May 2009) →