Steering Pad Switch Circuit
Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
This circuit sends an operation signal from the steering pad switch to the navigation receiver assembly.If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the navigation receiver assembly cannot be operated using the steering pad switch, and the navigation receiver assembly itself cannot function.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System) such as the airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).
| 1. INSPECT NAVIGATION RECEIVER ASSEMBLY |
Disconnect the navigation receiver assembly connector F38.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Condition
Specified condition
F38-7 (SW1) - F38-6 (SWG)
No switch is pushed
Approx. 100 kΩ
F38-7 (SW1) - F38-6 (SWG)
SEEK+ switch: push
0 to 2.5 Ω
F38-7 (SW1) - F38-6 (SWG)
SEEK- switch: push
Approx. 0.3 kΩ
F38-7 (SW1) - F38-6 (SWG)
VOL+ switch: push
Approx. 1 kΩ
F38-7 (SW1) - F38-6 (SWG)
VOL- switch: push
Approx. 3.1 kΩ
F38-8 (SW2) - F38-6 (SWG)
No switch is pushed
Approx. 100 kΩ
F38-8 (SW2) - F38-6 (SWG)
MODE switch: push
0 to 2.5 Ω
F38-8 (SW2) - F38-6 (SWG)
VOICE switch: push
Approx. 3.1 kΩ
F38-8 (SW2) - F38-6 (SWG)
ON HOOK switch: push
Approx. 0.3 kΩ
F38-8 (SW2) - F38-6 (SWG)
OFF HOOK switch: push
Approx. 1 kΩ
|
|
||||
| OK | ||
| ||
| 2. INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector a1.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Condition
Specified condition
a1-10 (AU1) - a1-8 (EAU)
No switch is pushed
Approx. 100 kΩ
a1-10 (AU1) - a1-8 (EAU)
SEEK+ switch: push
0 to 2.5 Ω
a1-10 (AU1) - a1-8 (EAU)
SEEK- switch: push
Approx. 0.3 kΩ
a1-10 (AU1) - a1-8 (EAU)
VOL+ switch: push
Approx. 1 kΩ
a1-10 (AU1) - a1-8 (EAU)
VOL- switch: push
Approx. 3.1 kΩ
a1-9 (AU2) - a1-8 (EAU)
No switch is pushed
Approx. 100 kΩ
a1-9 (AU2) - a1-8 (EAU)
MODE switch: push
0 to 2.5 Ω
a1-9 (AU2) - a1-8 (EAU)
VOICE switch: push
Approx. 3.1 kΩ
a1-9 (AU2) - a1-8 (EAU)
ON HOOK switch: push
Approx. 0.3 kΩ
a1-9 (AU2) - a1-8 (EAU)
OFF HOOK switch: push
Approx. 1 kΩ
|
|
||||
| OK | |
| 3. INSPECT SPIRAL CABLE |
Disconnect the a1 steering pad switch assembly and E18 spiral cable connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Spiral cable position
Specified condition
a1-8 (EAU) - E18-4 (EAU)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
a1-10 (AU1) - E18-6 (AU1)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
a1-9 (AU2) - E18-5 (AU2)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
- NOTICE:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may cause airbag deployment. Be sure to read the page shown in the brackets.
- HINT:
- Removal (Click here)
- Installation (Click here)
- Removal (Click here)
|
|
||||
| OK | ||
| ||
