2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Door Courtesy Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

The main body ECU detects the condition of the door courtesy switches.

WIRING DIAGRAM

B110597E14

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester main switch on.

  1. Select the items below in the DATA LIST, and read the display on the intelligent tester.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -
    P Door Courtesy SW
    Passenger side door courtesy switch signal / ON or OFF
    ON: Passenger side door is open
    OFF: Passenger side door is closed
    -
    RR Door Courtesy SW
    Rear RH door courtesy switch signal / ON or OFF
    ON: Rear right door is open
    OFF: Rear right door is closed
    -
    RL Door Courtesy SW
    Rear LH door courtesy switch signal / ON or OFF
    ON: Rear left door is open
    OFF: Rear right door is closed
    -

    OK:
    Normal conditions listed above are displayed.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT DOOR COURTESY SWITCH
  1. Inspect the front door courtesy switch (Click here).

  1. Inspect the rear door courtesy switch (Click here).

    OK:
    Door courtesy switches are normal.



NG
REPLACE DOOR COURTESY SWITCH
OK


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR COURTESY SWITCH)

  1. E108574E39
    Check the harness and connector between the main body ECU and door courtesy switches (passenger side and rear RH).
    1. Disconnect the E6 main body ECU connector.

    2. Disconnect the O10 rear RH door courtesy switch connector.

    3. Disconnect the O6 or N6 passenger side door courtesy switch.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E6-5 (RCTY) (*4) - O10-1 (Rear RH)
      Always
      Below 1 Ω
      E6-7 (RCTY) (*3) - O10-1 (Rear RH)
      Always
      Below 1 Ω
      E6-21 (PCTY) - O6-1 (*1)
      Always
      Below 1 Ω
      E6-21 (PCTY) - N6-1 (*2)
      Always
      Below 1 Ω
      E6-5 (RCTY) (*4) - Body ground
      Always
      10 kΩ or higher
      E6-7 (RCTY) (*3) - Body ground
      Always
      10 kΩ or higher
      E6-21 (PCTY) - Body ground
      Always
      10 kΩ or higher

      HINT:
      *1: LHD
      *2: RHD
      *3: with Smart Entry and Start System
      *4: without Smart Entry and Start System

  1. E121486E06
    Check the harness and connector between the instrument panel J/B assembly and rear LH door courtesy switch.
    1. Disconnect the IO instrument panel J/B assembly connector.

    2. Disconnect the N13 rear LH door courtesy switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      IO-7 (LCTY) - N13-1 (Rear LH)
      Always
      Below 1 Ω
      IO-7 (LCTY) - Body ground
      Always
      10 kΩ or higher

  1. E121487E05
    Check the harness and connector between the main body ECU and driver side door courtesy switch.
    1. Disconnect the E7 main body ECU connector.

    2. Disconnect the N6 or O6 driver side door courtesy switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E7-24 (DCTY) - N6-1 (*1)
      Always
      Below 1 Ω
      E7-24 (DCTY) - O6-1 (*2)
      Always
      Below 1 Ω
      E7-24 (DCTY) - Body ground
      Always
      10 kΩ or higher

      HINT:
      *1: LHD
      *2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


← Door Courtesy Switch Circuit (Jun 2006 – May 2009)Door LOCK Position Circuit (Jun 2006 – May 2009) →