2006-2011 Camry Aurion · Service Manual BODY

Driver Side Power Window Motor Circuit

Circuit diagnosis · Vehicles built from Jun 2006

DESCRIPTION

This circuit transmits signals from the power window regulator master switch assembly to the power window regulator motor (Driver side).

WIRING DIAGRAM

B137064E09
B137065E19

INSPECTION PROCEDURE


1. INSPECT POWER WINDOW REGULATOR MOTOR

  1. B127535E01
    without Jam protection:Remove the power window motor.
    1. Apply battery voltage to the motor connector according to the table below.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1and 2.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Motor gear rotates clockwise
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Motor gear rotates counterclockwise

with Jam protection:

  1. B145500E01
    Remove the power window motor.
    1. Apply battery voltage to the motor connector according to the table below.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1, 2, 4, 7 and 10.

      OK:
      Switch Condition
      Measurement Condition
      Specified Condition
      Manual Operation
      Battery positive (+) → Terminal 2 (B)
      Battery negative (-) → Terminal 1 (E), 7 (DWN1)
      Motor gear rotates counterclockwise
      Battery positive (+) → Terminal 2 (B)
      Battery negative (-) → Terminal 1 (E), 10 (UP1)
      Motor gear rotates clockwise
      Auto Operation
      Battery positive (+) → Terminal 2 (B)
      Battery negative (-) → Terminal 1 (E), 4 (AUTO), 7 (DWN1)
      Motor gear rotates counterclockwise
      Battery positive (+) → Terminal 2 (B)
      Battery negative (-) → Terminal 1 (E), 4 (AUTO), 10 (UP1)
      Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR
OK


2. CHECK WIRE HARNESS (WINDOW REGULATOR MOTOR - WINDOW REGULATOR MASTER SWITCH)

  1. B137061E05
    without Jam protection:Disconnect the M1 and I4 connectors.
    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-3 (U) - I4-2
      Always
      Below 1 Ω
      M1-4 (D) - I4-1
      Always
      Below 1 Ω
      M1-3 (U) - Body ground
      Always
      10 kΩ or higher
      M1-4 (D) - Body ground
      Always
      10 kΩ or higher

  1. B164437E04
    with Jam protection:Disconnect the M1 (*1), L1 (*2) and I5 (*1), H10 (*2) connectors.

    HINT:
    1. *1: LHD models
    2. *2: RHD models

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LHD models:
      Tester Connection
      Condition
      Specified Condition
      M1-8 (U) - I5-10 (UP1)
      Always
      Below 1 Ω
      M1-5 (D) - I5-7 (DWN1)
      Always
      Below 1 Ω
      M1-8 (U) - Body ground
      Always
      10 kΩ or higher
      M1-5 (D) - Body ground
      Always
      10 kΩ or higher
      RHD models:
      Tester Connection
      Condition
      Specified Condition
      L1-1 (U) - H10-10 (UP1)
      Always
      Below 1 Ω
      L1-5 (D) - H10-7 (DWN1)
      Always
      Below 1 Ω
      L1-1 (U) - Body ground
      Always
      10 kΩ or higher
      L1-5 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Rear Power Window Switch RH Circuit (from Oct 2006)Front Passenger Side Power Window Motor Circuit (from Jun 2006) →