Speaker Circuit
Circuit diagnosis · Vehicles built from Jun 2009
DESCRIPTION
If there is a short in this circuit, the radio and display assembly detects it and stops output to the speakers.Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display assembly or speakers.
If a short is detected in the speaker circuit, no sound can be heard from the speakers.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK HARNESS AND CONNECTOR |
Disconnect the F6 radio and display assembly connector.
Disconnect the F7 radio and display assembly connector.
Disconnect the I1 and H1 front No. 1 speaker connectors.
Disconnect the F21 and F23 front No. 2 speaker connectors.
Disconnect the O12 and O13 rear speaker connectors.
Measure the resistance between each of the front No. 2 speakers and the radio and display assembly to check for an open circuit in the wire harness.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F6-2 (FL+) - F21-2 (TWL+)
Always
Below 1 Ω
F6-6 (FL-) - F21-4 (TWL-)
Always
Below 1 Ω
F6-1 (FR+) - F23-2 (TWR+)
Always
Below 1 Ω
F6-5 (FR-) - F23-4 (TWR-)
Always
Below 1 Ω
Measure the resistance between each of the front No. 2 speakers and the front No. 1 speakers to check for an open circuit in the wire harness.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F21-1 (+) - I1-1
Always
Below 1 Ω
F21-3 (-) - I1-2
Always
Below 1 Ω
F23-1 (+) - H1-1
Always
Below 1 Ω
F23-3 (-) - H1-2
Always
Below 1 Ω
Measure the resistance between each of the rear speakers and the radio and display assembly to check for an open circuit in the wire harness.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F7-2 (RL+) - O12-1
Always
Below 1 Ω
F7-6 (RL-) - O12-2
Always
Below 1 Ω
F7-1 (RR+) - O13-1
Always
Below 1 Ω
F7-3 (RR-) - O13-2
Always
Below 1 Ω
Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F21-1 (+) - Body ground
Always
10 kΩ or higher
F21-3 (-) - Body ground
Always
10 kΩ or higher
F21-2 (TWL+) - Body ground
Always
10 kΩ or higher
F21-4 (TWL-) - Body ground
Always
10 kΩ or higher
F23-1 (+) - Body ground
Always
10 kΩ or higher
F23-3 (-) - Body ground
Always
10 kΩ or higher
F23-2 (TWR+) - Body ground
Always
10 kΩ or higher
F23-4 (TWR-) - Body ground
Always
10 kΩ or higher
O12-1 - Body ground
Always
10 kΩ or higher
O12-2 - Body ground
Always
10 kΩ or higher
O13-1 - Body ground
Always
10 kΩ or higher
O13-2 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT FRONT NO. 1 SPEAKER |
Resistance check

Measure the resistance between the terminals of the speaker.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I1-1 - I1-2
Always
3.2 to 4.8 Ω
H1-1 - H1-2
Always
3.2 to 4.8 Ω
- NOTICE:
- The speaker should not be removed to check resistance.
Text in Illustration *1
Component without harness connected
(Front No. 1 Speaker)
|
|
||||
| OK | |
| 3. INSPECT FRONT NO. 2 SPEAKER |
Resistance check

Measure the resistance between the terminals of the speaker.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F21-1 (+) - F21-2 (TWL+)
Always
Below 1 Ω
F21-3 (-) - F21-4 (TWL-)
Always
Below 1 Ω
F23-1 (+) - F23-2 (TWR+)
Always
Below 1 Ω
F23-3 (-) - F23-4 (TWR-)
Always
Below 1 Ω
- NOTICE:
- The speaker should not be removed to check resistance.
Text in Illustration *1
Component without harness connected
(Front No. 2 Speaker)
|
|
||||
| OK | |
| 4. INSPECT FRONT NO. 2 SPEAKER |
Check that the malfunction disappears when another speaker in good condition is installed.
- Standard:
- Malfunction disappears.
- HINT:
- Connect all the connectors to the front No. 2 speakers that were disconnected.
- If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
- Perform the above inspection on both LH and RH sides.
- Connect all the connectors to the front No. 2 speakers that were disconnected.
|
|
||||
| OK | ||
| ||
| 5. INSPECT REAR SPEAKER |
Resistance check

Measure the resistance between the terminals of the speaker.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O12-1 - O12-2
Always
3.2 to 4.8 Ω
O13-1 - O13-2
Always
3.2 to 4.8 Ω
- NOTICE:
- The speaker should not be removed to check resistance.
Text in Illustration *1
Component without harness connected
(Rear Speaker)
|
|
||||
| OK | ||
| ||
