2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

WIRING DIAGRAM

E186662E05

INSPECTION PROCEDURE


1. CHECK NAVIGATION RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      (for 2GR-FE RHD)
      B
      Automatic station search function stops on a station
      (except 2GR-FE RHD)
      C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (except 2GR-FE RHD) (Click here)
A


2. CHECK OPTIONAL COMPONENTS
  1. Check optional components (sun-shade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result:
      Result
      Proceed to
      Optional components are installed
      A
      Optional components are not installed
      B

      NOTICE:
      Do not remove optional components without the permission of the customer.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E050367
    Preparation for check
    1. Remove the antenna plug from the navigation receiver assembly.

  1. Check for noise

    1. Turn the ignition switch on (ACC) with the navigation receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire, or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speaker.

      OK:
      Noise occurs.

      Result:
      Result
      Proceed to
      OK
      A
      NG
      (for 2GR-FE RHD)
      B
      NG
      (except 2GR-FE RHD)
      C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (except 2GR-FE RHD) (Click here)
A


4. CHECK GLASS ANTENNA

  1. E111994E01
    Check for continuity of the antenna.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.

    OK:
    There is continuity in the antenna.



NG
REPAIR GLASS ANTENNA (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ANTENNA AMPLIFIER)
  1. Disconnect the F36 navigation receiver assembly connector.

  1. Disconnect the F15 antenna amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F36-8 (ANT) - F15-1 (B)
    Always
    Below 1 Ω
    F15-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E168580E07
    Reconnect the F36 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F15-1 (B) - Body ground
    Ignition switch on (IG)
    Radio switch on
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Antenna Amplifier)

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for 2GR-FE RHD)
    B
    NG
    (except 2GR-FE RHD)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (except 2GR-FE RHD) (Click here)
A


7. CHECK ANTENNA CORD
  1. Remove the antenna plug of the navigation receiver assembly and antenna.

  1. Measure the resistance between the antenna and navigation receiver assembly to check for an open circuit in the antenna cord.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard Resistance:
    10 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for 2GR-FE RHD)
    B
    NG
    (except 2GR-FE RHD)
    C



B
REPLACE ANTENNA CORD (for 2GR-FE RHD) (Click here)

C
REPLACE ANTENNA CORD (except 2GR-FE RHD) (Click here)
A


8. REPLACE ANTENNA AMPLIFIER
  1. Replace the antenna amplifier and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for 2GR-FE RHD)
    B
    NG
    (except 2GR-FE RHD)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (except 2GR-FE RHD) (Click here)
A

NORMAL OPERATION


← Radio Broadcast cannot be Received or Poor Reception (Oct 2006 – May 2009)Illumination for Panel Switch does not Come on with Tail Switch ON (Jun 2006 – Sep 2006) →