2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built from Jun 2009

WIRING DIAGRAM

E186662E14

INSPECTION PROCEDURE


1. CHECK RADIO AND DISPLAY ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      B
      (for 2GR-FE RHD)
      C
      (except 2GR-FE RHD)



B
REPLACE RADIO AND DISPLAY ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE RADIO AND DISPLAY ASSEMBLY (except 2GR-FE RHD) (Click here)
A


2. CHECK OPTIONAL COMPONENTS
  1. Check optional components (sunshade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result:
      Result
      Proceed to
      Optional components are installed
      A
      Optional components are not installed
      B

      NOTICE:
      Do not remove any optional components installed by the customer without his or her consent.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. CHECK RADIO AND DISPLAY ASSEMBLY

  1. E050367
    Preparation for check
    1. Remove the antenna plug from the radio and display assembly.

  1. Check for noise

    1. Turn the ignition switch on (ACC) with the radio and display assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the radio and display assembly antenna jack and check that noise can be heard from the speaker.

      OK:
      Noise can be heard from the speaker.

      Result:
      Result
      Proceed to
      OK
      A
      NG
      (for 2GR-FE RHD)
      B
      NG
      (except 2GR-FE RHD)
      C



B
REPLACE RADIO AND DISPLAY ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE RADIO AND DISPLAY ASSEMBLY (except 2GR-FE RHD) (Click here)
A


4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - ANTENNA AMPLIFIER)
  1. Disconnect the F6 radio and display assembly connector.

  1. Disconnect the F15 antenna amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-8 (ANT) - F15-1 (B)
    Always
    Below 1 Ω
    F6-8 (ANT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT RADIO AND DISPLAY ASSEMBLY
  1. Reconnect the F6 radio and display assembly connector.

  1. E150785E18
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F15-1 (B) - Body ground
    Ignition switch on (IG)
    Radio switch on
    11 to 14 V

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for 2GR-FE RHD)
    B
    NG
    (except 2GR-FE RHD)
    C

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Antenna Amplifier)



B
REPLACE RADIO AND DISPLAY ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE RADIO AND DISPLAY ASSEMBLY (except 2GR-FE RHD) (Click here)
A


6. CHECK ANTENNA CORD
  1. Remove the antenna plug of the radio and display assembly and antenna.

  1. Measure the resistance between the antenna and radio and display assembly to check for an open circuit in the antenna cord.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard Resistance:
    10 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for 2GR-FE RHD)
    B
    NG
    (except 2GR-FE RHD)
    C



B
REPLACE ANTENNA CORD (for 2GR-FE RHD) (Click here)

C
REPLACE ANTENNA CORD (except 2GR-FE RHD) (Click here)
A


7. REPLACE ANTENNA AMPLIFIER
  1. Replace the antenna amplifier and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for 2GR-FE RHD)
    B
    NG
    (except 2GR-FE RHD)
    C



B
REPLACE RADIO AND DISPLAY ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE RADIO AND DISPLAY ASSEMBLY (except 2GR-FE RHD) (Click here)
A

NORMAL OPERATION


← CD Sound Skips (from Jun 2009)Illumination for Panel Switch does not Come on with Tail Switch ON (from Jun 2009) →