2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION

The navigation receiver assembly receives the reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E194746E07

INSPECTION PROCEDURE


1. CHECK NAVIGATION RECEIVER ASSEMBLY (REVERSE SIGNAL INPUT)
  1. Disconnect the F13 connector from the navigation receiver assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F13-5 (REV) - Body ground
    Ignition switch on (IG), shift lever in R
    7 V or higher



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    for 2AZ-FE
    A
    for 2GR-FE
    B



B
Go to step 5
A


3. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the F13 connector from the navigation receiver assembly.

  1. Disconnect the C1 connector from the park/neutral position switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F13-5 (REV) - C1-1 (RL)
    Always
    Below 1 Ω
    F13-5 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Remove the park/neutral position switch assembly (Click here).

  1. E149961E13
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (RL) - 2 (RB)
    Shift lever in R
    Below 1 Ω
    1 (RL) - 2 (RB)
    Shift lever in any position except R
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Park/Neutral Position Switch Assembly)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for U250E) (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the F13 connector from the navigation receiver assembly.

  1. Disconnect the C1 connector from the park/neutral position switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F13-5 (REV) - C1-2 (RL)
    Always
    Below 1 Ω
    F13-5 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Remove the park/neutral position switch assembly (Click here).

  1. E149961E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (RL) - 1 (RB)
    Shift lever in R
    Below 1 Ω
    2 (RL) - 1 (RB)
    Shift lever in any position except R
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Park/Neutral Position Switch Assembly)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for U660E) (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← C1622 Open or Short Circuit in Back Camera Signal (from Jun 2009)Image from Camera for Rear View Monitor is Abnormal (from Jun 2009) →