2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

C1622 Open or Short Circuit in Back Camera Signal

Diagnostic trouble codes · Vehicles built from Jun 2009

DESCRIPTION

This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.
DTC No.
DTC Detection Condition
Trouble Area
C1622
Open or Short Circuit in Back Camera Signal
  1. Harness or connector
  2. Navigation receiver assembly
  3. Rear television camera assembly
  4. Luggage compartment door opener outer switch*1
  1. *1: for 2AZ-FE

WIRING DIAGRAM


for 2AZ-FE
E194623E01

for 2GR-FE
E183755E04

INSPECTION PROCEDURE


1. CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    for 2AZ-FE
    A
    for 2GR-FE
    B



B
Go to step 7
A


2. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - LUGGAGE COMPARTMENT DOOR OPENER SWITCH)
  1. Disconnect the F12 connector from the navigation receiver assembly and the S22 connector from the luggage compartment door opener outer switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S22-6 (CV+) - F12-22 (V+)
    Always
    Below 1 Ω
    S22-5 (CB+) - F12-24 (CA+)
    Always
    Below 1 Ω
    S22-1 (CGND) - F12-21 (CGND)
    Always
    Below 1 Ω
    S22-2 (CV-) - F12-23 (V-)
    Always
    Below 1 Ω
    S22-6 (CV+) - Body ground
    Always
    10 kΩ or higher
    S22-5 (CB+) - Body ground
    Always
    10 kΩ or higher
    S22-1 (CGND) - Body ground
    Always
    10 kΩ or higher
    S22-2 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER - LUGGAGE COMPARTMENT DOOR OPENER SWITCH)
OK


3. INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Reconnect the S22 connector to the luggage compartment door opener outer switch.

  1. E153726E11
    Reconnect the F12 connector to the navigation receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F12-23 (V-) - Body ground
    Always
    Below 1 Ω
    F12-21 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F12-24 (CA+) - F12-21 (CGND)
    Ignition switch on (IG)
    Shift lever in R
    5.5 to 7.0 V

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (except 2GR-FE RHD) (Click here)
OK


4. INSPECT REAR TELEVISION CAMERA ASSEMBLY

  1. E186086E01
    Check that the F12 and F36 connectors are connected to the navigation receiver assembly.

  1. E171712E02
    Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F12-22 (V+) - F36-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch on (IG), shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
Go to step 5
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (except 2GR-FE RHD) (Click here)

5. REPLACE LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH
  1. Replace the luggage compartment door opener outer switch with a new or normally functioning one (Click here).


NEXT


6. CHECK DTC OUTPUT (C1622)
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1622 is not output
    A
    DTC C1622 is output
    B



B
REPLACE REAR TELEVISION CAMERA ASSEMBLY (for 2AZ-FE) (Click here)
A

END

7. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - REAR TELEVISION CAMERA)
  1. Disconnect the F12 connector from the navigation receiver assembly.

  1. Disconnect the S17 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-2 (CV+) - F12-22 (V+)
    Always
    Below 1 Ω
    S17-4 (CB+) - F12-24 (CA+)
    Always
    Below 1 Ω
    S17-3 (CGND) - F12-21 (CGND)
    Always
    Below 1 Ω
    S17-1 (CV-) - F12-23 (V-)
    Always
    Below 1 Ω
    S17-2 (CV+) - Body ground
    Always
    10 kΩ or higher
    S17-4 (CB+) - Body ground
    Always
    10 kΩ or higher
    S17-3 (CGND) - Body ground
    Always
    10 kΩ or higher
    S17-1 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER - REAR TELEVISION CAMERA)
OK


8. INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Reconnect the S17 connector to the rear television camera assembly.

  1. E153726E11
    Reconnect the F12 connector to the navigation receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F12-23 (V-) - Body ground
    Always
    Below 1 Ω
    F12-21 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F12-24 (CA+) - F12-21 (CGND)
    Ignition switch on (IG)
    Shift lever in R
    5.5 to 7.0 V

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (for 2GR-FE RHD) (Click here)
OK


9. INSPECT REAR TELEVISION CAMERA ASSEMBLY

  1. E186086E01
    Check that the F12 and F36 connectors are connected to the navigation receiver assembly.

  1. E171712E02
    Check the waveform of the rear television camera assembly using an oscilloscope.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F12-22 (V+) - F36-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch on (IG), shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (for 2GR-FE) (Click here)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (for 2GR-FE RHD) (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Jun 2009)Reverse Signal Circuit (from Jun 2009) →