2006-2011 Camry Aurion · Service Manual BODY

TERMINALS OF ECU

System information · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (LHD models)
B137056E03
  1. Disconnect the M1 switch connector.

  2. Measure the voltage and resistance of each terminal according to the value(s) in the table below.

    Standard resistance:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (M1-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω


    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (M1-6) - E (M1-1)
    GR - W-B
    Power supply
    Ignition switch on (IG)
    10 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the M1 switch connector and reset the power window motor.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    with Jam protection:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (M1-8) - E (M1-1)
    G - W-B
    Power window motor UP output
    Ignition switch on (IG), driver side power window switch OFF → UP (Manual operation)
    10 to 14 V → 0 V
    A (M1-4) - E (M1-1)
    B - W-B
    Power window motor AUTO UP output
    Ignition switch on (IG), driver side power window fully open → driver side power window switch UP (AUTO UP position) → driver side power window fully closed
    10 to 14 V → 0 V → 10 to 14 V
    Power window motor AUTO DOWN output
    Ignition switch on (IG), driver side power window fully closed → driver side power window switch DOWN (AUTO UP position) → driver side power window fully open
    10 to 14 V → 0 V → 10 to 14 V
    D (M1-5) - E (M1-1)
    R - W-B
    Power window motor DOWN output
    Ignition switch on (IG), driver side power window switch OFF → DOWN (Manual operation)
    10 to 14 V → 0 V
    U (M1-16) - E (M1-1)
    W - W-B
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (M1-15) - E (M1-1)
    R - W-B
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation)
    0 V → 10 to 14 V
    U (M1-12) - E (M1-1)
    L - W-B
    Power window motor UP output
    Ignition switch on (IG), rear LH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (M1-13) - E (M1-1)
    B - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear LH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    U (M1-10) - E (M1-1)
    Y - W-B
    Power window motor UP output
    Ignition switch on (IG), rear RH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (M1-18) - E (M1-1)
    LG - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear RH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    without Jam protection:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (M1-3) - E (M1-1)
    G - W-B
    Power window motor UP output
    Ignition switch on (IG), driver side power window switch OFF → UP (Manual operation)
    10 to 14 V → 0 V
    D (M1-4) - E (M1-1)
    R - W-B
    Power window motor DOWN output
    Ignition switch on (IG), driver side power window fully open → driver side power window switch UP (AUTO UP position) → driver side power window fully closed
    10 to 14 V → 0 V → 10 to 14 V
    Power window motor AUTO DOWN output
    Ignition switch on (IG), driver side power window fully closed → driver side power window switch DOWN (AUTO UP position) → driver side power window fully open
    10 to 14 V → 0 V → 10 to 14 V
    U (M1-16) - E (M1-1)
    W - W-B
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (M1-15) - E (M1-1)
    R - W-B
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation)
    0 V → 10 to 14 V
    U (M1-12) - E (M1-1)
    L - W-B
    Power window motor UP output
    Ignition switch on (IG), rear LH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (M1-13) - E (M1-1)
    B - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear LH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    U (M1-10) - E (M1-1)
    Y - W-B
    Power window motor UP output
    Ignition switch on (IG), rear RH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (M1-18) - E (M1-1)
    LG - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear RH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (RHD models)
B137056E05
  1. Disconnect the L1 switch connector.

  2. Measure the voltage and resistance of each terminal according to the value(s) in the table below.

    Standard resistance:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (L1-9) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω


    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (L1-6) - E (L1-9)
    GR - W-B
    Power supply
    Ignition switch on (IG)
    10 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L1 switch connector and reset the power window motor.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (L1-1) - E (L1-9)
    BE - W-B
    Power window motor UP output
    Ignition switch on (IG), driver side power window switch OFF → UP (Manual operation)
    10 to 14 V → 0 V
    A (L1-4) - E (L1-9)
    B - W-B
    Power window motor AUTO UP output
    Ignition switch on (IG), driver side power window fully open → driver side power window switch UP (AUTO UP position) → driver side power window fully closed
    10 to 14 V → 0 V → 10 to 14 V
    Power window motor AUTO DOWN output
    Ignition switch on (IG), driver side power window fully closed → driver side power window switch DOWN (AUTO UP position) → driver side power window fully open
    10 to 14 V → 0 V → 10 to 14 V
    D (L1-5) - E (L1-9)
    V - W-B
    Power window motor DOWN output
    Ignition switch on (IG), driver side power window switch OFF → DOWN (Manual operation)
    10 to 14 V → 0 V
    D (L1-10) - E (L1-9)
    B - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear LH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    U (L1-12) - E (L1-9)
    W - W-B
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (L1-13) - E (L1-9)
    R - W-B
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation)
    0 V → 10 to 14 V
    D (L1-15) - E (L1-9)
    LG - W-B
    Power window motor DOWN output
    Ignition switch on (IG), rear RH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    U (L1-16) - E (L1-9)
    Y - W-B
    Power window motor UP output
    Ignition switch on (IG), rear RH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    U (L1-18) - E (L1-9)
    L - W-B
    Power window motor UP output
    Ignition switch on (IG), rear LH side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER)
B137057E07
  1. Disconnect the H6 (I9) switch connector.

  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (3) - Body ground
    GR - Body ground
    Power supply
    Ignition switch on (IG)
    10 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the H6 (I9) switch connector and reset the power window motor.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (4) - Body ground
    G - Body ground
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (1) - Body ground
    Y - Body ground
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation)
    0 V → 10 to 14 V

    If the result is not as specified, the power window regulator switch assembly may have a malfunction.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR LH)
B137057E02
  1. Disconnect the K1 switch connector.

  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (K1-3) - Body ground
    R - Body ground
    Power supply
    Ignition switch on (IG)
    10 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K1 switch connector and reset the power window motor.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (K1-4) - Body ground
    V - Body ground
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (K1-1) - Body ground
    R - Body ground
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation)
    0 V → 10 to 14 V

    If the result is not as specified, the power window regulator switch assembly may have a malfunction.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH)
B137057E03
  1. Disconnect the J1 switch connector.

  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (J1-3) - Body ground
    R - Body ground
    Power supply
    Ignition switch on (IG)
    10 to 14 V

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J1 switch connector and reset the power window motor.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (J1-4) - Body ground
    V - Body ground
    Power window motor UP output
    Ignition switch on (IG), front passenger side power window switch OFF → UP (Manual operation)
    0 V → 10 to 14 V
    D (J1-1) - Body ground
    R - Body ground
    Power window motor DOWN output
    Ignition switch on (IG), front passenger side power window switch OFF → DOWN (Manual operation)
    0 V → 10 to 14 V

    If the result is not as specified, the power window regulator switch assembly may have a malfunction.

← TERMINALS OF ECU (Oct 2006 – May 2009)DIAGNOSIS SYSTEM (Jun 2006 – Sep 2006) →