2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Headlight (HI-BEAM) Circuit

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

When the low beam headlights are on, and the dimmer switch is turned to the HIGH position, the main body ECU turns the high beam headlights on.

HINT:
  1. When a short circuit occurs between the power distributor and high beam headlight, the power distributor stops the high beam headlight relay operation (Fail-safe function).
  2. The high beam headlight relay is built into the power distributor, so unlike conventional relays, it cannot be removed for inspection.


WIRING DIAGRAM

E121490E09
E133294E02

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the item below in the ACTIVE TEST and then check that the relay operates.

    Main Body (Main Body ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Headlight (HI)
    High beam headlights
    ON / OFF
    -

    OK:
    High beam headlight relay operates. (High beam headlights illuminate.)



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

  1. E121528E04
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    ID-3 (HRLY) - Body ground
    Light control switch OFF → HEAD
    10 to 14 V → Below 1 V
    ID-9 (DIM) - Body ground
    Light control switch in HEAD and dimmer switch LOW → HIGH
    10 to 14 V → Below 1 V



OK
Go to step 6
NG


3. CHECK HARNESS AND CONNECTOR (ENGINE ROOM J/B ASSEMBLY - BATTERY AND BODY GROUND)

  1. B074501E17
    Disconnect the 1G engine room J/B assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1G-1 - Body ground
    Always
    10 to 14 V

  1. E121481E01
    Disconnect the 1E engine room J/B assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1E-11 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Reconnect the 1G and 1E engine room J/B assembly connectors.

  1. E121531E01
    Disconnect the 1D engine room J/B assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1D-8 - Body ground
    Always
    10 to 14 V
    1D-9 - Body ground
    Always
    10 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (POWER DISTRIBUTOR)
OK


5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM J/B ASSEMBLY - INSTRUMENT PANEL J/B ASSEMBLY)
  1. Reconnect the 1D engine room J/B assembly connector.

  1. E121479E04
    Disconnect the ID instrument panel J/B connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    ID-3 (HRLY) - Body ground
    Always
    10 to 14 V
    ID-9 (DIM) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6. CHECK HARNESS AND CONNECTOR (SHORT IN RELAY-DRIVEN CIRCUIT)

  1. E121471E01
    Remove the H-LP (RH) fuse from the engine room J/B assembly.

  1. Turn the light control switch to the HEAD position.

  1. Turn the dimmer switch to the HIGH position.

  1. Check if the high beam headlight LH illuminates.

  1. Turn the dimmer switch to the LOW position.

  1. Install the H-LP (RH) fuse and remove the H-LP (LH) fuse.

  1. Turn the dimmer switch to the HIGH position.

  1. Check if the high beam headlight RH illuminates.

    OK:
    Either high beam headlight LH or RH illuminates.



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (SHORT CIRCUIT BETWEEN FUSE AND BULB)
NG


7. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

  1. E121532E02
    Remove the H-LP (RH) fuse and H-LP (LH) fuse from the engine room J/B assembly.

  1. Measure the voltage between the loading slot of each fuse and body ground.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    H-LP (RH) Terminal - Body ground
    Light control switch in HEAD and dimmer switch in HIGH
    10 to 14 V
    H-LP (LH) Terminal - Body ground
    Light control switch in HEAD and dimmer switch in HIGH
    10 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (POWER DISTRIBUTOR)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (OPEN CIRCUIT BETWEEN FUSE AND BODY GROUND)


← Headlight Relay Circuit (from Oct 2006)Front Fog Light Circuit (from Oct 2006) →