2006-2011 Camry Aurion · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

HINT:
  1. Use the same procedures for the RHD and LHD.
  2. The procedures listed below are for the LHD.


1. PRECAUTION
Click here.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. DRAIN BRAKE FLUID

NOTICE:
  1. Stop the engine and depress the brake pedal several times until no vacuum is left in the brake booster.
  2. If the brake fluid leaks onto any painted surface, wash off and remove the brake fluid completely.


4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for LHD)

  1. A144946E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).

  1. A146036
    Disconnect the No. 2 ventilation hose from the air cleaner hose.

  1. A135668
    Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.

  1. A146037
    Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


5. REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for LHD)

  1. A134905
    Disconnect the hose clamp.

  1. Remove the 3 bolts and air cleaner case.


6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E135589
    Disconnect the connector.

  1. E135590
    Remove the 4 bolts and the windshield wiper motor and link assembly.


7. REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY

  1. C141972E01
    Disengage the clamp.

  1. Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.


8. REMOVE BRAKE BOOSTER ASSEMBLY (for LHD)
Click here.

9. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


11. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


12. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)

  1. B149938
    Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the No. 1 instrument panel sub-assembly.


13. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

  1. B149936
    Disengage the 3 claws and the 2 clips.

  1. Disconnect the connector and remove the No. 1 instrument panel sub-assembly.


14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

  1. B144612
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.


15. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133985E01
    Remove the 2 clips.

  1. Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.


16. REMOVE COMBINATION METER ASSEMBLY

  1. B152781E01
    Remove the 4 screws <E>.

  1. Disconnect each connector and remove the combination meter assembly.


17. DISCONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

  1. C135429
    Remove the clip and pin, and disconnect the push rod clevis from the clutch pedal.


18. DISCONNECT CLUTCH RESERVOIR TUBE

  1. C135418
    Using pliers, grip the claws of the clip and slide the clip to disconnect the tube from the clutch master cylinder.

    HINT:
    Use a container to catch the fluid.


19. DISCONNECT CLUTCH LINE

  1. C135419E01
    Using SST, disconnect the clutch line.
    SST
    09023-00101  

    HINT:
    Use a container to catch the fluid.


20. REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (for LHD)

  1. C135416
    Remove the 2 nuts and clutch master cylinder.

  1. Remove the gasket from the clutch master cylinder assembly.


21. REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (for RHD)

  1. C135417
    Remove the 2 nuts and clutch master cylinder.

  1. Remove the gasket from the clutch master cylinder assembly.

← REMOVAL (Jun 2006 – Sep 2006)REMOVAL (from Jun 2009) →