TERMINALS OF ECU
System information · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| CHECK TRANSPONDER KEY AMPLIFIER |
Disconnect the E25 amplifier connector and measure the resistance between the terminal of the wire harness side connector and body ground.


If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E25-7) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
Reconnect the E25 amplifier connector and measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, the amplifier may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
VC5 (E25-1) - AGND (E25-7)
O - V
Power source
No key is in ignition key cylinder
Below 1 V
Key is in ignition key cylinder
4.6 to 5.4 V
CODE (E25-4) - AGND (E25-7)
W - V
Demodulated signal of key code data
No key is in ignition key cylinder
Below 1 V
Key is in ignition key cylinder
Waveform 1
TXCT (E25-5) - AGND (E25-7)
GR - V
Key code output signal
No key is in ignition key cylinder
Below 1 V
Key is in ignition key cylinder
Waveform 2
AGND (E25-7) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
Inspect using an oscilloscope.
Waveform 1 (Reference)

Terminal
CODE (E25-4) - AGND (E25-7)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Key is in ignition key cylinder
Waveform 2 (Reference)

Terminal
TXCT (E25-5) - AGND (E25-7)
Tool Setting
2 V/DIV., 10 ms./DIV.
Condition
Key is in ignition key cylinder
| CHECK TRANSPONDER KEY ECU ASSEMBLY |
Disconnect the E15 ECU connector and measure the resistance and voltage according to the value(s) in the table below.


If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (E15-16) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B (E15-1) - GND (E15-16)
W - W-B
Battery
Always
10 to 14 V
IG (E15-2) - GND (E15-16)
B - W-B
Ignition switch signal
Ignition switch OFF
Below 1 V
Ignition switch ON
10 to 14 V
KSW (E15-3) - GND (E15-16)
B - W-B
Unlock warning switch signal
No key is in ignition key cylinder
10 kΩ or higher
Key is in ignition key cylinder
Below 1 Ω
Reconnect the E15 ECU connector and measure the voltage according to the value(s) in the table below.
If the result is not as specified, the ECU may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E15-5) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
KSW (E15-3) - GND (E15-16)
B - W-B
Unlock warning switch signal
No key is in ignition key cylinder
10 to 14 V
Key is in ignition key cylinder
Below 1 V
VC5 (E15-14) - AGND (E15-5)
O - V
Power source
No key is in ignition key cylinder
Below 1 V
Key is in ignition key cylinder
4.6 to 5.4 V
TXCT (E15-4) - AGND (E15-5)
GR - V
Transponder key amplifier communication signal
No key is in ignition key cylinder
Below 1 V
Key is in ignition key cylinder
Waveform 1
CODE (E15-15) - AGND (E15-5)
W - V
Transponder key amplifier communication signal
No key is in ignition key cylinder
Below 1 V
Key is in ignition key cylinder
Waveform 2
EFIO (E15-13) - GND (E15-16)
L - W-B
ECM output signal
Ignition switch OFF
Below 1 V
Ignition switch ON
Waveform 3
EFII (E15-12) - GND (E15-16)
G - W-B
ECM input signal
Ignition switch OFF
Below 1 V
Ignition switch ON
Waveform 4
D (E15-9) - GND (E15-16)
R - W-B
Diagnostic tester communication
Without communication
Below 1 V
During communication
Pulse generation
CTY (E15-7) - GND (E15-16)
Y - W-B
Door courtesy signal
Switch pushed
10 to 14 V
Switch free
Below 1 V
IND (E15-8) - GND (E15-16)
P - W-B
Security indicator signal
Security indicator light is on
10 to 14 V
Security indicator light is off
Below 1 V
Inspect using an oscilloscope.
Waveform 1 (Reference)

Terminal
TXCT (E15-4) - AGND (E15-5)
Tool Setting
2 V/DIV., 10 ms./DIV.
Condition
Key is in ignition key cylinder
Waveform 2 (Reference)

Terminal
CODE (E15-15) - AGND (E15-5)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Key is in ignition key cylinder
Waveform 3 (Reference)

Terminal
EFIO (E15-13) - GND (E15-16)
Tool Setting
2 V/DIV., 1 s./DIV.
Condition
Ignition switch ON
Waveform 4 (Reference)

Terminal
EFII (E15-12) - GND (E15-16)
Tool Setting
2 V/DIV., 1 s./DIV.
Condition
Ignition switch ON
| CHECK ECM |
Disconnect the C24 ECM connector and measure the resistance between the terminal of the wire harness side connector and body ground.


If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E1 (C24-104) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the C24 ECM connector. Measure the voltage between each terminal of the connector according to the value(s) in the table below.
If the result is not as specified, the ECM may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
IMI (A24-11) - E1 (C24-104)
Y - W-B
Transponder key ECU input signal
Ignition switch OFF
Below 1 V
Ignition switch ON
Waveform 1
IMO (A24-10) - E1 (C24-104)
G - W-B
Transponder key ECU output signal
Ignition switch OFF
Below 1 V
Ignition switch ON
Waveform 2
Inspect using an oscilloscope.
Waveform 1 (Reference)

Terminal
IMI (A24-11) - E1 (C24-104)
Tool Setting
2 V/DIV., 1 s./DIV.
Condition
Ignition switch ON
Waveform 2 (Reference)

Terminal
IMO (A24-10) - E1 (C24-104)
Tool Setting
2 V/DIV., 1 s./DIV.
Condition
Ignition switch ON