2006-2011 Camry Aurion · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


CHECK TRANSPONDER KEY AMPLIFIER

  1. Disconnect the E25 amplifier connector and measure the resistance between the terminal of the wire harness side connector and body ground.
    B065593E20

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E25-7) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E25 amplifier connector and measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    VC5 (E25-1) - AGND (E25-7)
    BE - V
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V
    CODE (E25-4) - AGND (E25-7)
    W - V
    Demodulated signal of key code data
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    TXCT (E25-5) - AGND (E25-7)
    GR - V
    Key code output signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    AGND (E25-7) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, the amplifier may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139208E01
      Waveform 1 (Reference)
      Terminal
      CODE (E25-4) - AGND (E25-7)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder

    2. B139205E01
      Waveform 2 (Reference)
      Terminal
      TXCT (E25-5) - AGND (E25-7)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY

  1. Disconnect the E15 ECU connector and measure the resistance and voltage according to the value(s) in the table below.
    B088367E04

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (E15-16) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (E15-1) - GND (E15-16)
    W - W-B
    Battery
    Always
    10 to 14 V
    IG (E15-2) - GND (E15-16)
    B - W-B
    Ignition switch signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    10 to 14 V
    KSW (E15-3) - GND (E15-16)
    B - W-B
    Unlock warning switch signal
    No key is in ignition key cylinder
    10 kΩ or higher
    Key is in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E15 ECU connector and measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E15-5) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    KSW (E15-3) - GND (E15-16)
    B - W-B
    Unlock warning switch signal
    No key is in ignition key cylinder
    10 to 14 V
    Key is in ignition key cylinder
    Below 1 V
    VC5 (E15-14) - AGND (E15-5)
    BE - V
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V
    TXCT (E15-4) - AGND (E15-5)
    GR - V
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    CODE (E15-15) - AGND (E15-5)
    W - V
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    EFIO (E15-13) - GND (E15-16)
    L - W-B
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 3
    EFII (E15-12) - GND (E15-16)
    G - W-B
    ECM input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 4
    D (E15-9) - GND (E15-16)
    R - W-B
    Diagnostic tester communication
    Without communication
    Below 1 V
    During communication
    Pulse generation
    CTY (E15-7) - GND (E15-16)
    Y - W-B
    Door courtesy signal
    Switch pushed
    10 to 14 V
    Switch free
    Below 1 V
    IND (E15-8) - GND (E15-16)
    P - W-B
    Security indicator signal
    Security indicator light is on
    10 to 14 V
    Security indicator light is off
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139205E01
      Waveform 1 (Reference)
      Terminal
      TXCT (E15-4) - AGND (E15-5)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder

    2. B139208E01
      Waveform 2 (Reference)
      Terminal
      CODE (E15-15) - AGND (E15-5)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder

    3. B139206E01
      Waveform 3 (Reference)
      Terminal
      EFIO (E15-13) - GND (E15-16)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

    4. B139207E01
      Waveform 4 (Reference)
      Terminal
      EFII (E15-12) - GND (E15-16)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 2AZ-FE)

  1. Disconnect the C24 ECM connector and measure the resistance between the terminal of the wire harness side connector and body ground.
    A107881E65

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (C24-104) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the C24 ECM connector. Measure the voltage between each terminal of the connector according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IMI (A24-11) - E1 (C24-104)
    Y - W-B
    Transponder key ECU input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 1
    IMO (A24-10) - E1 (C24-104)
    G - W-B
    Transponder key ECU output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 2
    If the result is not as specified, the ECM may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139206E01
      Waveform 1 (Reference)
      Terminal
      IMI (A24-11) - E1 (C24-104)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

    2. B139207E01
      Waveform 2 (Reference)
      Terminal
      IMO (A24-10) - E1 (C24-104)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 2GR-FE)

  1. Disconnect the C55 (for LHD) or C58 (for RHD) ECM connector and measure the resistance between the terminal of the wire harness side connector and body ground.
    A107881E81

    for LHD 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (C55-81) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    for RHD 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (C58-81) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the C55 (for LHD) or C58 (for RHD) ECM connector. Measure the voltage between each terminal of the connector according to the value(s) in the table below.

    for LHD 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IMI (A55-11) - E1 (C55-81)
    Y - W-B
    Transponder key ECU input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 1
    IMO (A55-10) - E1 (C55-81)
    G - W-B
    Transponder key ECU output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 2
    for RHD 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IMI (A24-11) - E1 (C58-81)
    Y - W-B
    Transponder key ECU input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 1
    IMO (A24-10) - E1 (C58-81)
    G - W-B
    Transponder key ECU output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 2
    If the result is not as specified, the ECM may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139206E01
      Waveform 1 (Reference)
      Terminal
      LHD
      IMI (A55-11) - E1 (C55-81)
      RHD
      IMI (A24-11) - E1 (C58-81)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

    2. B139207E01
      Waveform 2 (Reference)
      Terminal
      LHD
      IMO (A55-10) - E1 (C55-81)
      RHD
      IMO (A24-10) - E1 (C58-81)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

← TERMINALS OF ECU (Oct 2006 – May 2009)DIAGNOSIS SYSTEM (from Jun 2006) →