Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
4.
REMOVE V-BANK COVER SUB-ASSEMBLY
Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.
NOTICE:
Attempting to disengage both front and rear clips at the same time may cause the cover to break.
5.
REMOVE COOL AIR INTAKE DUCT SEAL
Remove the 7 clips and intake duct seal.
6.
REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Disconnect the 3 vacuum hoses.
Disconnect the mass air flow meter connector (*1).
Disconnect the No. 2 ventilation hose (*2).
Disconnect the hose band (*3).
Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.
7.
REMOVE AIR CLEANER INLET SUB-ASSEMBLY
Remove the 2 bolts, clamp and air cleaner inlet.
8.
REMOVE NO. 1 AIR CLEANER INLET
Remove the bolt and No. 1 air cleaner inlet.
9.
REMOVE FRONT BUMPER ASSEMBLY
Put protective tape around the front bumper assembly.
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
HINT:
Use the same procedure for the RH side and LH side.
Remove the 8 screws, 3 clips and 2 radiator grille protectors.
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
HINT:
Use the same procedure for the RH side and LH side.
w/ Clearance Sonar System:
Disconnect the 2 connectors.
w/ Fog Light:
Disconnect the 2 connectors.
w/ Headlight Cleaner System:
Disconnect the 2 connectors.
Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.
Remove the front bumper assembly.
10.
REMOVE FRONT BUMPER ENERGY ABSORBER
Remove the front bumper energy absorber from the front bumper reinforcement sub-assembly.
11.
DISCONNECT RADIATOR RESERVOIR TANK HOSE
Disconnect the radiator reserve tank hose from the radiator assembly.
12.
DISCONNECT RADIATOR INLET HOSE
Disconnect the radiator inlet hose from the radiator assembly.
13.
DISCONNECT RADIATOR OUTLET HOSE
Disconnect the radiator outlet hose from the radiator assembly.
14.
DISCONNECT NO. 1 OIL COOLER INLET HOSE
Disconnect the No. 1 oil cooler inlet hose from the radiator assembly.
15.
DISCONNECT NO. 1 OIL COOLER OUTLET HOSE
Disconnect the No. 1 oil cooler outlet hose from the radiator assembly.
16.
REMOVE HOOD LOCK ASSEMBLY (for LHD)
Remove the 3 bolts.
Disconnect the hood lock control cable.
Remove the hood lock assembly.
17.
REMOVE HOOD LOCK ASSEMBLY (for RHD)
Disconnect the connector.
Remove the 3 bolts.
Disconnect the hood lock control cable.
Remove the hood lock assembly.
18.
REMOVE RADIATOR SUPPORT UPPER
Disconnect the horn connectors.
Remove the 5 bolts and radiator support upper.
19.
REMOVE FAN SHROUD
Remove the 3 clamps and connector.
Release the 3 snap fits and lift the fan assembly with motor from the radiator.
20.
REMOVE RADIATOR ASSEMBLY
Remove the 4 bolts and separate the condenser assembly from the radiator assembly.
Remove the radiator assembly from the body.
21.
REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
22.
REMOVE RADIATOR SUPPORT LOWER
Remove the 2 radiator support lowers from the radiator assembly.