2006-2011 Camry Aurion · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Type)

  1. B136575E01
    Detach the 2 front hooks of the seat cushion from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.


4. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

  1. B134699E01
    Detach the 2 front hooks of the seat cushion from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the step above for the other hook.

  1. Remove the seat cushion.


5. REMOVE REAR FLOOR SERVICE HOLE COVER

  1. A129478
    Remove the rear floor service hole cover.

  1. Disconnect the fuel pump connector.


6. SEPARATE FUEL PUMP TUBE SUB-ASSEMBLY

  1. A129479E02
    Remove the tube joint clip, and pull out the fuel pump tube.

    NOTICE:
    1. Check that there is no dirt around the fuel tube joint before this work and clean the dirt away.
    2. Be careful of dirt and mud because the fuel tube joint has O-rings to seal the fuel tube connector and fuel suction plate.
    3. Do not use any tools in this work.
    4. Do not bend or twist the nylon tube by force.
    5. After disconnecting, cover the fuel tube joint with a plastic bag.
    6. When the fuel tube joint and fuel suction plate are stuck, pinch the fuel tank tube between fingers, and turn it carefully to release. Disconnect the fuel tank tube.


7. REMOVE FUEL TANK VENT TUBE SET PLATE

  1. A129480
    Remove the 8 bolts and set plate.


8. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

  1. A139190
    Pull out the fuel suction tube from the fuel tank.

    NOTICE:
    1. Do not damage the fuel pump filter.
    2. Be careful that the arm of the sender gauge does not bend.

  1. A136023E01
    Remove the gasket from the fuel suction tube.


9. DRAIN FUEL

10. REMOVE CENTER EXHAUST PIPE ASSEMBLY

  1. Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.

    A146049

  1. Remove the gasket from the front exhaust pipe.


11. DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

  1. A135222
    Remove the set bolt and set nut of the No. 2 parking brake cable assembly.


12. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. A135223
    Remove the set bolt and set nut of the No. 3 parking brake cable assembly.


13. REMOVE REAR STABILIZER BAR NO. 1 BRACKET

  1. A136008E01
    Remove the 4 bolts and 2 rear stabilizer bar No. 1 brackets.


14. REMOVE FUEL TANK PROTECTOR LOWER CENTER

  1. A135224
    Remove the 4 bolts and fuel tank protector.


15. REMOVE FUEL TANK ASSEMBLY

  1. A121573E02
    Disconnect the fuel pump tube.

    1. Pinch the tab of the retainer to disengage the lock claws and pull it down as shown in the illustration.

    2. Pull out the fuel tank main tube.

      NOTICE:
      1. Check that there is no dirt or other foreign objects around the connector before this operation and clean the connector as necessary.
      2. It is necessary to prevent mud or dirt from entering the quick connector. If mud enters the connector, the O-rings may not seal properly.
      3. Remove the quick connector by hand.
      4. Do not bend or twist the nylon tube. Protect the connector by covering it with a plastic bag.
      5. If the pipe and connector are stuck, try wiggling or pushing and pulling the connector to release it and pull the connector off of the pipe carefully.

  1. A135227
    Disconnect the fuel emission hose from the charcoal canister.

  1. A142097
    Place a transmission jack under the fuel tank assembly.

  1. A135228E01
    Remove the 2 set bolts of the fuel tank bands. (*1)

  1. Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose. (*2)

  1. Loosen the hose clamp bolt and disconnect the fuel tank breather hose. (*3)

  1. Remove the fuel tank.

  1. A079478
    Remove the 2 pins and 2 fuel tank bands as shown in the illustration.

  1. A136004
    Remove the 4 clip nuts.


16. REMOVE NO. 2 FUEL TANK PROTECTOR

  1. A184695E01
    Remove the No. 2 fuel tank protector by sliding as shown in the illustration.


17. REMOVE NO. 3 FUEL TANK PROTECTOR

  1. A184696E01
    Remove the No. 3 fuel tank protector by sliding as shown in the illustration.


18. REMOVE FUEL CUT OFF WITH TUBE VALVE ASSEMBLY

  1. A060493E01
    Insert a clip remover between the cut off valve and the gasket and remove the cut off valve by gradually pushing it upward.

    NOTICE:
    1. Work carefully to maintain the sealing integrity of the valve as it is made from resin and easy to be damaged if forcibly removing and installing it.
    2. Be sure to install a new cut off valve and gasket.

  1. Separate the 2 tube clamps.

  1. Remove the 2 breather tube gaskets.


19. REMOVE FUEL PUMP TUBE SUB-ASSEMBLY

  1. A136006
    Remove the fuel pump tube from the fuel main tube support and tube clamp.


20. REMOVE FUEL MAIN TUBE SUPPORT

  1. A079481
    Remove the bolt and tube support.


21. REMOVE NO. 4 FUEL TUBE CLAMP

  1. A136011
    Remove the 3 clamps.


22. REMOVE NO. 1 FUEL TANK CUSHION

  1. A136010E01
    Remove the No. 1 fuel tank cushion.


23. REMOVE NO. 2 FUEL TANK CUSHION
  1. Remove the 7 No. 2 fuel tank cushions.

← REMOVAL (Jun 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →