DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| DIAGNOSIS SYSTEM |
Inspect the battery voltage.
- Standard voltage:
- 11 to 14 V
The vehicle's ECU uses ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

- HINT:
- Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the intelligent tester. If the screen displays a communication error message, a problem exists on either the vehicle side or the tester side.
If the communication is still impossible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.Symbols (Terminal No.)
Terminal Description
Condition
Specified Condition
CG (4) - Body ground
Chassis ground
Always
Below 1 Ω
SG (5) - Body ground
Signal ground
Always
Below 1 Ω
BAT (16) - Body ground
Battery positive
Always
9 to 14 V
CANH (6) - CANL (14)
CAN bus line
Ignition switch off*
54 to 69 Ω
CANH (6) - Battery positive
HIGH-level CAN bus line
Ignition switch off*
6 kΩ or higher
CANH (6) - CG (4)
HIGH-level CAN bus line
Ignition switch off*
200 Ω or higher
CANL (14) - Battery positive
LOW-level CAN bus line
Ignition switch off*
6 kΩ or higher
CANL (14) - CG (4)
LOW-level CAN bus line
Ignition switch off*
200 Ω or higher
- NOTICE:
- *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.
| DIAGNOSIS |
- NOTICE:
- When releasing the parking brake, set chocks to hold the vehicle for safety.
If the skid control ECU detects a malfunction, the ABS, VSC (without multi information display), and BRAKE warning lights, and master caution and SLIP indicator lights will come on and the multi information display shows a warning message in order to warn the driver.

The table below indicates which lights will come on when there is a malfunction in a particular function.
○: Light ONItem/Trouble Area
ABS
EBD
BA
TRC
VSC
ABS Warning Light
○
○
○
-
-
BRAKE Warning Light
-
○
-
-
-
VSC Warning
○
○
○
○
○
SLIP Indicator Light
○
○
○
○
○
-: Light OFF- The DTCs are simultaneously stored in the memory. The DTCs can be read by connecting the SST between terminals TC and CG of the DLC3 and observing the blinking pattern of the ABS warning light by connecting the intelligent tester (Click here).
- This system has a signal check function (TEST MODE) (Click here).
The DTC can be read by connecting the intelligent tester and observing the blinking pattern of the ABS warning light.
- The DTCs are simultaneously stored in the memory. The DTCs can be read by connecting the SST between terminals TC and CG of the DLC3 and observing the blinking pattern of the ABS warning light by connecting the intelligent tester (Click here).
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
- HINT:
- When the parking brake is applied or the level of the brake fluid is low, the BRAKE warning light comes on.
Release the parking brake.

- NOTICE:
- Before releasing the parking brake, move the shift lever to the P position for safety.
When the ignition switch on (IG), check that the ABS, VSC (without multi information display), and BRAKE warning lights, and master caution and SLIP indicator lights come on for approximately 3 seconds.
- HINT:
- If the ECU stores any DTCs, the ABS, BRAKE, and VSC (without multi information display) warning lights, and SLIP indicator light come on.
- If the indicator remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
Trouble Area
See procedure
ABS warning light (Remains on)
Click here
ABS warning light (Does not come on)
Click here
BRAKE warning light (Remains on)
Click here
BRAKE warning light (Does not come on)
Click here
VSC warning light (Remains on)
Click here
VSC warning light (Does not come on)
Click here
SLIP indicator light (Remains on)
Click here
SLIP indicator light (Does not come on)
Click here
| SYMPTOM SIMULATION |
- HINT:
- The most difficult case in troubleshooting is when no symptoms occur. In such cases, a thorough customer problem analysis must be carried out. Then the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be reproduced. No matter how experienced or skilled a technician may be, if he proceeds to troubleshoot without confirming the problem symptoms, he will likely overlook something important and make a wrong guess at some points in the repair operation. This leads to a standstill in troubleshooting.
Vibration method: When vibration seems to be the major cause.

- HINT:
- Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch on (IG)).
Slightly vibrate the part of the sensor considered to be the problem cause with your fingers and check whether the malfunction occurs.
Slightly shake the connector vertically and horizontally.
- HINT:
- Shaking the relays too strongly may result in open relays.
Slightly shake the wire harness vertically and horizontally. The connector joint and fulcrum of the vibration are the major areas to be checked thoroughly.