DISASSEMBLY
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
REMOVE LUGGAGE COMPARTMENT DOOR COVER
|
 |
- Using a clip remover, remove the 13 clips and luggage compartment door cover.
| 2.
REMOVE REAR LIGHT ASSEMBLY LH
|
 |
- Disconnect the connector and clamp.
Remove the 4 nuts and the rear light assembly.
| 3.
REMOVE REAR LIGHT ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 4.
REMOVE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
|
 |
- Disengage the clamp.
Disconnect the cable and connector.
Remove the 2 bolts and luggage compartment door lock assembly.
| 5.
REMOVE LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY |
 |
- Disconnect the cable and connector.
- Remove the 2 nuts and the luggage compartment door lock cylinder assembly.
| 6.
REMOVE REAR SPOILER (w/ Rear Spoiler)
|
 |
- HINT:
- When removing the rear spoiler, heat the vehicle body and rear spoiler using a heat light.
- Heating temperature:
Item
|
Temperature
|
Vehicle Body
|
40 to 60°C (104 to 140°F)
|
Rear Spoiler
|
20 to 30°C (68 to 86°F)
|
- NOTICE:
- Do not heat the vehicle body and rear spoiler excessively.
- Disconnect the connector.
Remove the 2 nuts.
Disengage the 2 clips and peel off the 2 No. 1 rear spoiler protectors, then remove the rear spoiler.


| 7.
REMOVE LUGGAGE DOOR OPENING SWITCH ASSEMBLY (w/ Smart Entry and Start System)
|
 |
Disconnect the connector.
- Remove the 2 nuts and the luggage door opening switch assembly.
| 8.
REMOVE BACK DOOR GARNISH RETAINER (w/ Smart Entry and Start System)
|
 |
without Parking Assist Monitor System:
- Remove the 2 nuts.
- Disengage the 2 claws and remove the back door garnish retainer.
| 9.
REMOVE TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)
|
 |
- Disengage the camera connector clamp.
Disconnect the television camera connector.
Remove the 2 nuts.
- Disengage the 2 claws to remove the television camera assembly as shown in the illustration.
| 10.
REMOVE LUGGAGE COMPARTMENT OUTSIDE DOOR GARNISH SUB-ASSEMBLY (w/o Smart Entry and Start System)
|
 |
- Put protective tape around the luggage compartment door outside garnish sub-assembly.
- Remove the 6 nuts.
- Using a moulding remover, disengage the 4 clips and remove the luggage compartment door outside garnish sub-assembly.
- HINT:
- Disengage either lock on the clip to prevent the clip from breaking.
| 11.
REMOVE LUGGAGE COMPARTMENT OUTSIDE DOOR GARNISH SUB-ASSEMBLY (w/ Smart Entry and Start System)
|
 |
- Put protective tape around the luggage compartment door outside garnish sub-assembly.
- Remove the 2 nuts.
- Using a moulding remover, disengage the 4 clips and remove the luggage compartment door outside garnish sub-assembly.
- HINT:
- Disengage either lock on the clip to prevent the clip from breaking.
| 12.
REMOVE LICENSE PLATE LIGHT ASSEMBLY LH
|
 |
Disconnect the connector.
- Disengage the 2 claws and remove the license plate light assembly as shown in the illustration.
| 13.
REMOVE LICENSE PLATE LIGHT ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH side and the LH side.