ON-VEHICLE INSPECTION
Inspection · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| INSPECT DRIVER SIDE SEAT BELT WARNING |
Turn the ignition switch on (IG).
When the driver seat belt is not fastened with the passenger seat not occupied, check that the driver seat belt warning light on the combination meter blinks.
When the driver seat belt is fastened, check that the driver seat belt warning light on the combination meter is off.
| INSPECT PASSENGER SIDE SEAT BELT WARNING (for LHD) |
Turn the ignition switch on (IG).
When the front passenger seat belt is not fastened with the passenger seat occupied and the driver seat not occupied, check that the front passenger seat belt warning light on the clock display blinks.
When the front passenger seat belt is fastened with the passenger seat occupied, check that the front passenger seat belt warning light on the clock display is off.
| REMOVE PASSENGER SIDE BELT WARNING (for 2GR-FE RHD) |
Turn the ignition switch on (IG).
When the front passenger seat belt is not fastened with the passenger seat occupied and the driver seat not occupied, check that the seat belt warning light on the combination meter assembly blinks.
When the front passenger seat belt is fastened with the passenger seat occupied, check that the seat belt warning light on the combination meter assembly is off.
- HINT:
- The driver seat belt warning light and passenger seat belt warning light are the same indicator light.
| INSPECT SEAT BELT WARNING BUZZER |
- HINT:
- If the buzzer does not sound, the buzzer cancel setting may be set to ON.
- Only the intelligent tester can change the buzzer cancel setting to OFF (the legally required warning buzzer cannot be cancelled*).
- If the buzzer does not sound, the buzzer cancel setting may be set to ON.
- *: for LHD
Check legally required warning buzzer operation.*
- HINT:
- The legally required warning buzzer is the buzzer that sounds when the ignition switch is turned on (IG) and the driver seat belt is not fastened. The buzzer sounds in order to warn the driver regardless of the vehicle speed.
Turn the ignition switch on (IG).
Check that the legally required warning buzzer sounds 1.8 seconds after the ignition switch is turned from off to on (IG).
- HINT:
- The legally required warning buzzer sounds at intervals of 1.2 seconds for 6 seconds.
- *: for LHD
Check seat belt buzzer operation.
- HINT:
- The seat belt buzzer is the buzzer that sounds to warn the driver that the driver or front passenger*3 seat belt is not fastened when the vehicle speed is 20 km/h (12.5 mph) or more.
Start the engine.
When the vehicle is driven at approximately 20 km/h (12.5 mph) or more with the driver or front passenger*3 seat belt not fastened, check that the buzzer in the combination meter assembly sounds at intervals of 1.2 seconds for 9.6*1 or 30*2 seconds.
With the belt remaining unfastened, check that the buzzer changes and sounds at intervals of 0.4 seconds for 20*1 or 90*2 seconds.
Check that the buzzer stops 29.6 seconds*1 or 2 minutes*2 after the buzzer starts sounding.
After the buzzer has stopped, turn the ignition switch off and then start the engine again. Drive the vehicle at approximately 20 km/h (12.5 mph) or more with the driver or front passenger*3 seat belt not fastened, and then check that the buzzer sounds again.
After the buzzer has stopped, fasten the driver and front passenger*3 seat belts. Drive the vehicle at approximately 20 km/h (12.5 mph) or more and unfasten the driver or front passenger*3 seat belt, and then check that the buzzer sounds again.
After the buzzer has stopped, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12.5 mph) or more, and then check that the buzzer sounds again.
- *1: for LHD
- *2: for RHD
- *3: for LHD, 2GR-FE RHD
- *1: for LHD
