INSTALLATION
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat) |
for LHD:
Install the front seat inner belt assembly with the nut.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector. (for Driver seat)


Connect the connectors and engage each clamp.

Engage the 2 hooks.

for RHD:
Install the front seat inner belt assembly with the nut.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector. (for Driver seat)


Connect the connector and engage the 2 clamps.

Engage the 2 hooks.

| 2. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Power Seat) |
for LHD:

Install the front seat inner belt assembly with the nut.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector.
Connect the connector and engage each clamps.

Engage the 2 hooks.

for RHD:
Install the front seat inner belt assembly with the nut.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector. (for Driver seat)


Connect the connector and engage the 2 clamps.

Engage the 2 hooks.

| 3. INSTALL FRONT INNER SEAT CUSHION SHIELD (for Manual Seat) |
Engage the 2 claws.

Install the front inner seat cushion shield with the screw.
| 4. INSTALL FRONT INNER SEAT CUSHION SHIELD (for Power Seat) |
Install the front inner seat cushion shield with the screw.

Engage the 3 claws.
| 5. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat) |
Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.
Connect the connector and clamp.
Move the front seat assembly to the rearmost position by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Temporarily install the front seat track bracket with the 2 bolts.

Move the front seat assembly fully forward by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Temporarily install the rear seat track bracket with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Move the front seat assembly fully forward by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 6. INSTALL INNER SEAT TRACK BRACKET COVER (for Manual Seat) |
Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the inner seat track bracket cover inner to engage claw B.
| 7. INSTALL OUTER SEAT TRACK BRACKET COVER (for Manual Seat) |
Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the outer seat track bracket cover to engage claw B.
| 8. INSTALL FRONT SEAT ASSEMBLY (for Power Seat) |
Place the seat in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Temporarily install the front side of the front seat assembly with the 2 bolts.

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Temporarily install the rear side of the front seat assembly with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 9. INSTALL INNER SEAT TRACK BRACKET COVER (for Power Seat) |
Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the inner seat track bracket cover to engage claw B.
| 10. INSTALL OUTER SEAT TRACK BRACKET COVER (for Power Seat) |
Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track cover to engage claw B.
| 11. INSTALL FRONT SEAT HEADREST ASSEMBLY |
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat) |
| 13. INSPECT SLIDE ADJUSTER LOCK (for Manual Seat) |
| 14. INSPECT FRONT SEAT ASSEMBLY (for Power Seat) |
Inspect the power seat operation.
| 15. INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag) |
