2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built from Jun 2009


1. REMOVE LUGGAGE COMPARTMENT FLOOR MAT

2. REMOVE SPARE WHEEL COVER CLAMP

3. REMOVE SPARE WHEEL COVER ASSEMBLY

4. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

  1. B136879
    Remove the 2 screws and the 2 No. 1 luggage compartment trim hooks.


5. REMOVE REAR FLOOR FINISH PLATE

  1. B136852
    Disengage the 7 clips and remove the rear floor finish plate.


6. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH

  1. B136855
    Remove the 2 clips and the luggage compartment inner trim cover RH.


7. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/o Rear Lower Spoiler)

  1. B137209
    Remove the 3 screws and rear quarter panel mudguard sub-assembly LH.


8. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/o Rear Lower Spoiler)

HINT:
Use the same procedure for the RH side and LH side.


9. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler)

  1. w/ Clearance Sonar System:

    1. B149446
      Disconnect the connector.

    2. Disengage the grommet.

  1. B137211E01
    Put protective tape around the rear bumper assembly.

  1. B137212
    Using a screwdriver, open the 2 rear bumper plates.

    HINT:
    Tape the screwdriver tip before use.

  1. B137214
    Remove the 6 screws and 2 clips.

  1. B137215
    Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the rear bumper assembly.


10. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler)

  1. B138885E01
    Remove the 4 screws, 2 clips, 3 nuts and rear floor board.


11. REMOVE REAR BUMPER ASSEMBLY (w/ Rear Lower Spoiler)

  1. w/ Clearance Sonar System:

    1. B149446
      Disconnect the connector.

    2. Disengage the grommet.

  1. B146330E01
    Put protective tape around the rear bumper assembly.

  1. B146331
    Using a screwdriver, open the 2 rear bumper plates.

    HINT:
    Tape the screwdriver tip before use.

  1. B140154
    Remove the 6 screws.

  1. B146332
    Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the rear bumper assembly.


12. REMOVE NO. 2 ULTRASONIC SENSOR
  1. Disconnect each sensor connector.

  1. E206037
    Remove the sensor retainer as shown in the illustration.

  1. E205958
    While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 2 ultrasonic sensor.

    HINT:
    The type of the claws on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.


13. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER

  1. E134862
    Disengage the 2 claws and remove the No. 2 ultrasonic sensor retainer from the rear bumper.

← COMPONENTS (from Jun 2009)INSTALLATION (from Jun 2009) →