2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. REMOVE HEADLIGHT BACK COVER (for Halogen Headlight)

  1. E182825
    Turn the headlight back cover in the direction indicated by the arrow shown in the illustration, and remove it.


2. REMOVE HEADLIGHT BACK COVER (for HID Headlight)

  1. E182849
    Release the set spring as shown in the illustration.

  1. Loosen the 2 screws and remove the headlight back cover.

    HINT:
    The screws cannot be removed from the cover.


3. REMOVE HEADLIGHT BACK COVER GASKET (for HID Headlight)
  1. Remove the headlight back cover gasket.

    NOTICE:
    After the headlight back cover gasket is removed, be sure to replace it with a new one. Failure to do this may cause water ingress.


4. REMOVE NO. 1 HEADLIGHT BULB (for Halogen Headlight)
  1. Disconnect the connector.

  1. E182827
    Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

    NOTICE:
    Do not touch the bulb glass.


5. REMOVE NO. 1 HEADLIGHT BULB (for HID Headlight)
  1. Disconnect the connector.

  1. E182828
    Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

    NOTICE:
    Do not touch the bulb glass.


6. REMOVE NO. 2 HEADLIGHT BULB (for Halogen Headlight)

  1. E182829
    Remove the No. 2 headlight bulb as shown in the illustration.


7. REMOVE DISCHARGE HEADLIGHT BULB (for HID Headlight)

  1. E182832
    Separate the light control ECU socket as shown in the illustration.

  1. E182833E01
    Release the set spring and remove the discharge headlight bulb as shown in the illustration.


8. REMOVE FRONT TURN SIGNAL LIGHT BULB

  1. E182834
    Turn the front turn signal light bulb and front turn signal light socket in the direction indicated by the arrow shown in the illustration, and remove them as a unit.

  1. Remove the front turn signal light bulb from the front turn signal light socket.


9. REMOVE CLEARANCE LIGHT BULB

  1. E182835
    Turn the clearance light bulb and clearance light socket in the direction indicated by the arrow shown in the illustration, and remove them as a unit.

  1. Remove the clearance light bulb from the clearance light socket.


10. REMOVE LIGHT CONTROL ECU SUB-ASSEMBLY (for HID Headlight)

  1. E182836
    Remove the 4 screws.

  1. E182837
    Disconnect the connector and remove the light control ECU sub-assembly.


11. REMOVE HEADLIGHT GASKET (for HID Headlight)
  1. Remove the headlight gasket.

    NOTICE:
    After the headlight gasket is removed, be sure to replace it with a new one. Failure to do this may cause water ingress.


12. REMOVE HEADLIGHT LEVELING MOTOR (for HID Headlight)

  1. E192592
    Align the notches of the headlight leveling motor and housing, and pull out the headlight leveling motor slightly.

  1. E131204
    Lower the tip of the headlight leveling motor to disengage it from the reflector and remove the headlight leveling motor.


13. REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING (for HID Headlight)
  1. Remove the headlight leveling motor base packing.

    NOTICE:
    After the headlight leveling motor base packing is removed, be sure to replace it with a new one. Failure to do this may cause water ingress.

← DISASSEMBLY (Oct 2006 – May 2009)ADJUSTMENT (Oct 2006 – May 2009) →