2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


CHECK MAIN BODY ECU (INSTRUMENT PANEL J/B)

  1. Disconnect the main body ECU (instrument panel J/B) connectors.
    B139428E01

  2. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    RCTY (E6-7) - Body ground
    GR - Body ground
    Rear courtesy light switch RH input
    Rear door RH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    PCTY (E6-21) - Body ground
    Y*1 - Body ground
    Passenger side courtesy light switch input
    Passenger side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    L*2 - Body ground
    LGCY (E6-25) - Body ground
    W - Body ground
    Luggage compartment door courtesy light switch input
    Luggage compartment door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    DCTY (E7-24) - Body ground
    L*1 - Body ground
    Driver side door courtesy light switch input
    Driver side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    Y*2 - Body ground
    ACC (IF-2) - Body ground
    L - Body ground
    Power supply
    Engine switch on (ACC)
    10 to 14 V
    IG (IF-11) - Body ground
    B - Body ground
    Power supply
    Engine switch on (IG)
    10 to 14 V
    ALTB (ID-16) - Body ground
    W - Body ground
    +B (power system alternator system) power supply
    Always
    10 to 14 V
    GND1 (IF-10) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND2 (IM-9) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    LCTY (IO-7) - Body ground
    LG - Body ground
    Rear courtesy light switch LH input
    Rear door LH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω

    HINT:
    *1: LHD
    *2: RHD

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body (instrument panel J/B) connectors.

  4. Measure the voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    TR+ (E7-1) - Body ground
    B - Body ground
    Luggage compartment door opener motor
    Luggage compartment door CLOSED (LOCKED) → OPEN (UNLOCKED)
    Below 1 V → 10 to 14 V*1
    HAZ (E8-4) - Body ground
    W - Body ground
    Turn signal flasher relay signal
    Any transmitter switch is pressed → not pressed
    Below 1 V → 10 to 14 V*2

    HINT:
    1. *1: When operating the motor.
    2. *2: When operating the answer back function.


CHECK CERTIFICATION ECU ASSEMBLY

  1. Disconnect the E58 ECU connector.
    E125964E04

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (E58-1) - E (E58-17)
    W - W-B
    Battery power supply
    Always
    10 to 14 V
    E (E58-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IG (E58-18) - E (E58-17)
    LG - W-B
    IG power supply
    Engine switch on (IG)
    10 to 14 V
    IG (E58-18) - E (E58-17)
    LG - W-B
    IG power supply
    Engine switch off
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E58 ECU connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BZR (E58-21) - Body ground
    BE - Body ground
    Wireless door lock buzzer
    Wireless door lock buzzer OFF → ON
    0 V → Pulse generation
    RC0 (E58-29) - E (E58-17)
    G - W-B
    Door control receiver power supply
    Engine switch off, all doors closed and transmitter switch not pressed
    Below 1 V
    RC0 (E58-29) - E (E58-17)
    G - W-B
    Door control receiver power supply
    Engine switch off, all doors closed and transmitter switch pressed
    4.6 to 5.4 V
    RDA (E58-38) - E (E58-17)
    Y - W-B
    Door control receiver output signal
    Engine switch off, all doors closed and transmitter switch not pressed
    10 to 14 V
    RDA (E58-38) - E (E58-17)
    Y - W-B
    Door control receiver output signal
    Engine switch off, all doors closed and transmitter switch pressed
    Pulse generation
    1. If the result is not as specified, the ECU may have a malfunction.

← TERMINALS OF ECU (Oct 2006 – May 2009)DIAGNOSIS SYSTEM (from Oct 2006) →