TERMINALS OF ECU
System information · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| CHECK MAIN BODY ECU (INSTRUMENT PANEL J/B) |
Disconnect the main body ECU (instrument panel J/B) connectors.


Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
RCTY (E6-7) - Body ground
GR - Body ground
Rear courtesy light switch RH input
Rear door RH CLOSED (OFF) → OPEN (ON)
10 kΩ or higher → Below 1 Ω
PCTY (E6-21) - Body ground
Y*1 - Body ground
Passenger side courtesy light switch input
Passenger side door CLOSED (OFF) → OPEN (ON)
10 kΩ or higher → Below 1 Ω
L*2 - Body ground
LGCY (E6-25) - Body ground
W - Body ground
Luggage compartment door courtesy light switch input
Luggage compartment door CLOSED (OFF) → OPEN (ON)
10 kΩ or higher → Below 1 Ω
DCTY (E7-24) - Body ground
L*1 - Body ground
Driver side door courtesy light switch input
Driver side door CLOSED (OFF) → OPEN (ON)
10 kΩ or higher → Below 1 Ω
Y*2 - Body ground
ACC (IF-2) - Body ground
L - Body ground
Power supply
Engine switch on (ACC)
10 to 14 V
IG (IF-11) - Body ground
B - Body ground
Power supply
Engine switch on (IG)
10 to 14 V
ALTB (ID-16) - Body ground
W - Body ground
+B (power system alternator system) power supply
Always
10 to 14 V
GND1 (IF-10) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
GND2 (IM-9) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
LCTY (IO-7) - Body ground
LG - Body ground
Rear courtesy light switch LH input
Rear door LH CLOSED (OFF) → OPEN (ON)
10 kΩ or higher → Below 1 Ω
- HINT:
- *1: LHD
- *2: RHD
Reconnect the main body (instrument panel J/B) connectors.
Measure the voltage between each terminal of the wire harness side connectors and body ground.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
TR+ (E7-1) - Body ground
B - Body ground
Luggage compartment door opener motor
Luggage compartment door CLOSED (LOCKED) → OPEN (UNLOCKED)
Below 1 V → 10 to 14 V*1
HAZ (E8-4) - Body ground
W - Body ground
Turn signal flasher relay signal
Any transmitter switch is pressed → not pressed
Below 1 V → 10 to 14 V*2
- HINT:
- *1: When operating the motor.
- *2: When operating the answer back function.
- *1: When operating the motor.
| CHECK CERTIFICATION ECU ASSEMBLY |
Disconnect the E58 ECU connector.


Measure the voltage and resistance of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
+B (E58-1) - E (E58-17)
W - W-B
Battery power supply
Always
10 to 14 V
E (E58-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
IG (E58-18) - E (E58-17)
LG - W-B
IG power supply
Engine switch on (IG)
10 to 14 V
IG (E58-18) - E (E58-17)
LG - W-B
IG power supply
Engine switch off
Below 1 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E58 ECU connector.
Measure the voltage of the connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BZR (E58-21) - Body ground
O - Body ground
Wireless door lock buzzer
Wireless door lock buzzer OFF → ON
0 V → Pulse generation
RC0 (E58-29) - E (E58-17)
G - W-B
Door control receiver power supply
Engine switch off, all doors closed and transmitter switch not pressed
Below 1 V
RC0 (E58-29) - E (E58-17)
G - W-B
Door control receiver power supply
Engine switch off, all doors closed and transmitter switch pressed
4.6 to 5.4 V
RDA (E58-38) - E (E58-17)
Y - W-B
Door control receiver input signal
Engine switch off, all doors closed and transmitter switch not pressed
10 to 14 V pulse generation at regular intervals
RDA (E58-38) - E (E58-17)
Y - W-B
Door control receiver input signal
Engine switch off, all doors closed and transmitter switch pressed
Pulse generation
- If the result is not as specified, the ECU may have a malfunction.
- If the result is not as specified, the ECU may have a malfunction.