2006-2011 Camry Aurion · Service Manual ENGINE

Power Source Mode does not Change to ON (IG)

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION

When the engine switch is pushed with the electrical key in the cabin, the main body ECU (instrument panel junction block assembly) receives signals to switch the power source mode.

HINT:
To allow use of the intelligent tester to inspect the push-button start function when the engine switch is off, repeat opening and closing any of the doors. Opening and closing a door establishes communication between the intelligent tester and the main body ECU (instrument panel junction block assembly). (Opening and closing a door can also be simulated by operating a door courtesy light switch.)


WIRING DIAGRAM

B157552E04

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. Check that the connectors are securely connected and the terminals are not deformed or loose.

    OK:
    The connectors are securely connected and the terminals are not deformed or loose.



NG
REPAIR OR REPLACE CONNECTORS
OK


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) - BATTERY)
  1. Disconnect the E6 and E7 connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-6 (AM1) - Body ground
    Always
    11 to 14 V
    E6-1 (AM2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) - BATTERY)
OK


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
  1. Disconnect the IF and IM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IF-10 (GND1) - Body ground
    Always
    Below 1 Ω
    IM-9 (GND2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - BODY GROUND)
OK


4. INSPECT RELAY (IG2 RELAY)

  1. B060778E73
    Remove the IG2 relay from the engine room relay block No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals between 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals between 1 and 2
    Below 1 Ω



NG
REPLACE RELAY (IG2 RELAY)
OK


5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU AND BODY GROUND)
  1. Remove the IG2 relay from the engine room relay block.

  1. Disconnect the E6 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room R/B IG2 relay terminal 1 - E6-11 (IG2D)
    Always
    Below 1 Ω
    Engine room R/B IG2 relay terminal 2 - Body ground
    Always
    Below 1 Ω
    E6-11 (IG2D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU AND BODY GROUND)
OK


6. INSPECT RELAY (IG1 RELAY)

  1. A092673E23
    Remove the IG1 relay from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


7. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - MAIN BODY ECU)
  1. Disconnect the II connector.

  1. Disconnect the E7 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    II-9 - E7-3 (IG1D)
    Always
    Below 1 Ω
    E7-3 (IG1D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - MAIN BODY ECU)
OK


8. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY AND BODY GROUND)
  1. Disconnect the IF and IA connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IF-10 - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    IA-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY AND BODY GROUND)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK


← Power Source Mode does not Change to ON (IG and ACC) (from Jun 2009)Power Source Mode does not Change to ON (ACC) (from Jun 2009) →