2006-2011 Camry Aurion · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY (for LHD)

  1. C132712
    Temporarily install the brake pedal support assembly with the bolt.

    NOTICE:
    Fully tighten the bolt after installing the brake booster assembly.

  1. C132711E01
    Temporarily install the No. 1 brake pedal support plate with 2 bolts (A) and bolt (B).

    NOTICE:
    Fully tighten 2 bolts (A) and bolt (B) after installing the brake booster assembly.

  1. Install the brake booster assembly (Click here).

  1. C132712
    Fully tighten the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. C132711E01
    Fully tighten 2 bolts (A) and bolt (B).

    Torque:
    Bolt (A):
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }
    Bolt (B):
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. C132710E01
    Engage the 2 clamps and connect the stop light switch connector.


2. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY (for RHD)

  1. C132836E02
    Temporarily install the brake pedal support assembly with the bolt and install the clamp.

  1. C132837E02
    Temporarily install the No. 1 brake pedal support plate with 2 bolts (A) and bolt (B).

    NOTICE:
    Fully tighten 2 bolts (A) and bolt (B) after installing the brake booster assembly.

  1. Install the brake booster assembly. (Click here)

  1. C132836E01
    Fully tighten the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. C132837E02
    Fully tighten 2 bolts (A) and bolt (B).

    Torque:
    Bolt (A):
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }
    Bolt (B):
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. C133309
    Connect the stop light switch connector.


3. INSTALL ACCELERATOR PEDAL ASSEMBLY (for RHD)

NOTICE:
  1. Avoid physical shock to the accelerator pedal assembly.
  2. Do not disassemble the accelerator pedal assembly.

  1. A135676
    Install the accelerator pedal assembly with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the accelerator pedal position sensor connector.


4. INSTALL BRAKE BOOSTER ASSEMBLY

HINT:
Refer to the procedures up to "INSTALL BRAKE BOOSTER". (Click here)


5. INSTALL COMBINATION METER ASSEMBLY

  1. B152781E01
    Connect each connector.

  1. Install the combination meter assembly with the 4 screws <E>.


6. INSTALL INSTRUMENT CLUSTER FINISH PANEL

  1. B133985E01
    Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel sub-assembly with the 2 clips.


7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL

  1. B144612
    Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


8. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
  1. Connect each connector.

  1. B149938
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


9. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
  1. Connect each connector.

  1. B149936
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH

  1. B147264E01
    Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Install the lower No. 1 instrument panel finish panel with the screw <B> and bolt <A>.


11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


12. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.

← REASSEMBLY (from Jun 2006)INSTALLATION (Oct 2006 – May 2009) →