Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009from Jun 2009
1.
INSTALL PARKING BRAKE PEDAL ASSEMBLY
Install the parking brake pedal assembly with the bolt and 2 nuts.
Torque:
39 N*m{
398 kgf*cm
, 29 ft.*lbf
}
Connect the parking brake switch connector.
Install the No. 1 parking brake cable assembly to the body with the bolt, the nut, and a new No. 1 parking brake cable clamp.
Torque:
Bolt:
15 N*m{
153 kgf*cm
, 11 ft.*lbf
}
Nut:
5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
NOTICE:
Make sure that the No. 1 parking brake cable clamp is installed in the correct direction as shown in the illustration.
Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable assembly.
2.
CONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY
Connect the No. 4 parking brake cable assembly to the No. 1 parking brake cable assembly.
Using SST and a wrench, hold the lock nut of the No. 1 parking brake cable and tighten the turnbuckle of the No. 4 parking brake cable assembly.
SST
09023-00101
Torque:
without SST:
5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
with SST:
5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
NOTICE:
Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
This torque is effective when SST is parallel to a torque wrench.
3.
INSTALL CENTER AIRBAG SENSOR ASSEMBLY
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Install the center airbag sensor assembly with the 3 bolts.
Torque:
17.5 N*m{
179 kgf*cm
, 13 ft.*lbf
}
NOTICE:
If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
Check that there is no looseness in the installation parts of the center airbag sensor assembly.
Connect the holder (with connectors).
Check that the water-proof sheet is properly set.
4.
INSTALL FLOOR SHIFT LEVER ASSEMBLY
Install the floor shift lever assembly with the 4 bolts.
Torque:
12 N*m{
122 kgf*cm
, 9 ft.*lbf
}
5.
INSTALL FLOOR CARPET BRACKET LH
6.
INSTALL FLOOR CARPET BRACKET RH
7.
INSTALL NO. 1 CONSOLE BOX DUCT
Install the No. 1 console box duct with the clip.
8.
INSTALL NO. 1 CONSOLE BOX INSERT FRONT
Engage the clip.
Install the No. 1 console box insert front with the 3 screws <F>.
9.
INSTALL NO. 2 CONSOLE BOX INSERT FRONT
Engage the clip.
Install the No. 2 console box insert front with the 3 screws <F>.
10.
INSTALL CONSOLE BOX ASSEMBLY
Install the 2 screws <F>.
Install the console box assembly with the 2 bolts <G>.
Engage the clamp.
11.
INSTALL CONSOLE BOX CARPET
Install the console box carpet.
12.
INSTALL CONSOLE BOX POCKET
Install the console box pocket.
13.
INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
Connect each connector.
Engage the 2 claws and 2 clips.
Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.
14.
INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY
Connect the connector.
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
15.
INSTALL POSITION INDICATOR HOUSING ASSEMBLY
Engage the 6 claws and the 3 clips to install the position indicator housing assembly.