2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL SHIFT LEVER ASSEMBLY

  1. C148665
    Connect the shift lock ECU connector and transmission control switch wire connector.

  1. C148666
    Install the shift lever assembly with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C148661
    Install the transmission control cable assembly as shown in the illustration.

    HINT:
    1. Install the transmission control cable assembly with the uneven surface facing up.
    2. Securely engage the claws of the transmission control cable assembly.


3. INSTALL CONSOLE BOX ASSEMBLY

  1. B158940
    Engage the 2 claws.

  1. B158939
    Install the 2 bolts.

  1. B158937
    Install the 3 screws.

  1. B158938
    Install the console box assembly with the 3 screws.

  1. B158936E01
    Engage the clamp.


4. INSTALL CONSOLE BOX CARPET

  1. B158935
    Install the console box carpet.


5. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Connect the connector.

  1. B158962
    Engage the 10 claws and install the upper console panel sub-assembly.


6. INSTALL UPPER CONSOLE PANEL FRONT GARNISH

  1. B158963
    Connect each connector.

  1. Engage the 6 claws and install the upper console panel front garnish.


7. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

  1. C147377
    Install the shift lever knob sub-assembly.


8. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B158922E01
    Engage the 3 claws and 3 clips.

  1. Install the screw <F> or <N>.

  1. Install the 3 screws <F>.

  1. Install the lower instrument panel sub-assembly with the bolt <D>.


9. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B158969E01
    Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover sub-assembly.


10. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


11. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


12. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B158913E01
    Install the air hose and connect each connector.

  1. Engage the claw and the 4 clips.

  1. Engage the 2 claws and the DLC3.

  1. Install the lower No. 1 instrument panel finish panel with the screw <F> and bolt <D>.


13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


14. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.9 N*m{ 70 kgf*cm , 61 in.*lbf }


16. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position.
    If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


17. ADJUST SHIFT LEVER POSITION
  1. Remove the cool air intake duct seal (Click here).

  1. Remove the air cleaner inlet assembly (Click here).

  1. Remove the air cleaner cap sub-assembly (Click here).

  1. Remove the air cleaner case sub-assembly (Click here).

  1. Remove the No. 1 air cleaner inlet (Click here).

  1. Move the shift lever to the N position.

  1. C132236
    Remove the nut and transmission control cable from the control shaft lever.

  1. C135733E01
    Align the protrusions of the park/neutral position switch.

  1. C135734E02
    Move the slider in the direction indicated by arrow A and pull up the lock piece in the direction indicated by arrow B.

    NOTICE:
    Do not damage the boot.

  1. C132236
    Install the transmission control cable assembly to the control shaft with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. If the control cable end is excessively pushed up, the shift lever cannot be adjusted.
    2. When tightening the nut, confirm that the control cable is properly stretched.

  1. C138300E01
    Push in the lock piece.

    NOTICE:
    Firmly push in the lock piece until the slider lock is engaged.

  1. Install the No. 1 air cleaner inlet (Click here).

  1. Install the air cleaner case sub-assembly (Click here).

  1. Install the air cleaner cap sub-assembly (Click here).

  1. Install the air cleaner inlet assembly (Click here).

  1. Install the cool air intake duct seal (Click here).

  1. Start the engine and make sure that the vehicle moves forward when moving the lever from the N to the D position and moves rearward when moving it to the R position. If it becomes hard to move the shift lever, readjust the shift lever position.

← REASSEMBLY (from Oct 2006)INSTALLATION (from Jun 2009) →