2006-2011 Camry Aurion · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for LHD)

  1. B146666E01
    Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.


2. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for RHD)

  1. B165278
    Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.


3. INSTALL FRONT SEATBACK ASSEMBLY (for LHD)

  1. w/o Airbag System:

    1. Install the front separate type seatback assembly to the front seatback spring assembly.

    2. B136594E01
      Engage the 3 hooks.

    3. Using hog ring pliers, install 2 new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. w/ Airbag System:

    1. Install the front separate type seatback assembly to the front seatback spring assembly.

    2. B165264
      Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

      NOTICE:
      1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
      2. Make sure that the strap is not twisted after installing the bracket.
      3. Install the bracket securely.

    3. B136594E01
      Engage the 3 hooks.

    4. Using hog ring pliers, install 2 new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, take care to minimize wrinkles as much as possible.


4. INSTALL FRONT SEATBACK ASSEMBLY (for RHD)

  1. for Except Sports Seat Type:

    1. Install the front seatback assembly to the front seatback spring assembly.

    2. B165280
      Install the front seatback cover bracket with the nut.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

      NOTICE:
      1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
      2. Make sure that the strap is not twisted after installing the bracket.
      3. Install the bracket securely.

    3. B149612E01
      Engage the 6 hooks.

    4. Using hog ring pliers, install 5 new hog rings.

    5. B165281E01
      Using hog ring pliers, install 3 new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. for Sports Seat Type:

    1. B165280
      Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

      NOTICE:
      1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
      2. Make sure that the strap is not twisted after installing the bracket.
      3. Install the bracket securely.

    2. Engage the 3 hooks.

    3. B165282E01
      Using hog ring pliers, install 2 new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, take care to minimize wrinkles as much as possible.


5. INSTALL FRONT SEAT HEADREST SUPPORT (for LHD)

  1. B134683
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


6. INSTALL FRONT SEAT HEADREST SUPPORT (for RHD)

  1. B146662
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


7. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for LHD)

  1. B134682E02
    Engage the 2 claws.

  1. Engage the 14 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


8. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for RHD)

  1. for Except Sports Seat Type:

    1. B165275
      Engage the 4 claws.

    2. Install the front seatback board sub-assembly with the 2 screws.

  1. for Sports Seat Type:

    1. B134682E02
      Engage the 2 claws.

    2. Engage the 14 claws.

    3. Install the front seatback board sub-assembly with the 2 screws.


9. INSTALL FRONT INNER SEAT CUSHION SHIELD (for LHD)

  1. B146655
    Install the front inner seat cushion shield with the screw.

  1. Engage the 3 claws.


10. INSTALL FRONT INNER SEAT CUSHION SHIELD (for RHD)

  1. B165271
    Engage the 3 claws.

  1. Install the front inner seat cushion shield with the screw.


11. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY (for LHD)

  1. B134673
    Connect the connector.

  1. Engage the 2 claws.

  1. Install the front seat cushion shield assembly with the 5 screws.

  1. B146651
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


12. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY (for RHD)

  1. B165271
    Engage the 3 claws.

  1. Install the front inner seat cushion shield with the screw.


13. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for LHD)

  1. B149597
    Install the slide and vertical power seat switch knob.


14. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for RHD)

  1. B147701
    Install the slide and vertical power seat switch knob.


15. INSTALL RECLINING POWER SEAT SWITCH KNOB (for LHD)

  1. B149596
    Install the reclining power seat switch knob.


16. INSTALL RECLINING POWER SEAT SWITCH KNOB (for RHD)

  1. B147702
    Install the reclining power seat switch knob.


17. INSTALL FRONT SEAT ASSEMBLY (for LHD)
  1. Place the seat in the cabin.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. B149590
    Temporarily install the front side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. B139102
    Temporarily install the rear side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


18. INSTALL FRONT SEAT ASSEMBLY (for RHD)
  1. Place the seat in the cabin.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. B147683
    Temporarily install the front side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. B147684
    Temporarily install the rear side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


19. INSTALL INNER SEAT TRACK BRACKET COVER (for LHD)

  1. B149588E01
    Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover to engage claw B.


20. INSTALL INNER SEAT TRACK BRACKET COVER (for RHD)
  1. Engage the 4 claws and install the front seat rear inner track bracket cover.


21. INSTALL OUTER SEAT TRACK BRACKET COVER (for LHD)

  1. B149587E01
    Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track cover to engage claw B.


22. INSTALL OUTER SEAT TRACK BRACKET COVER (for RHD)

  1. B147713
    Engage the 4 claws and install the front seat rear outer track bracket cover.


23. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LHD)

24. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RHD)

25. INSPECT SRS WARNING LIGHT (w/ Airbag System)
Inspect the SRS warning light. (Click here)

26. INSPECT FRONT SEAT ASSEMBLY
← INSPECTION (from Oct 2006)INSTALLATION (from Jun 2009) →