INSTALLATION
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for LHD) |
 |
- Install the lumbar support adjuster assembly with the 2 screws.
Connect the connector.
| 2.
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for RHD) |
 |
- Install the lumbar support adjuster assembly with the 2 screws.
Connect the connector.
| 3.
INSTALL FRONT SEATBACK ASSEMBLY (for LHD) |
 |
w/o Airbag System:
Install the front separate type seatback assembly to the front seatback spring assembly.
- Engage the 3 hooks.
Using hog ring pliers, install 2 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
w/ Airbag System:
Install the front separate type seatback assembly to the front seatback spring assembly.
- Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
- NOTICE:
- For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
- Make sure that the strap is not twisted after installing the bracket.
- Install the bracket securely.
- Engage the 3 hooks.
Using hog ring pliers, install 2 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 4.
INSTALL FRONT SEATBACK ASSEMBLY (for RHD) |
 |
for Except Sports Seat Type:
Install the front seatback assembly to the front seatback spring assembly.
- Install the front seatback cover bracket with the nut.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
- NOTICE:
- For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
- Make sure that the strap is not twisted after installing the bracket.
- Install the bracket securely.
- Engage the 6 hooks.
Using hog ring pliers, install 5 new hog rings.
- Using hog ring pliers, install 3 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
for Sports Seat Type:
- Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
- NOTICE:
- For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
- Make sure that the strap is not twisted after installing the bracket.
- Install the bracket securely.
Engage the 3 hooks.
- Using hog ring pliers, install 2 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 5.
INSTALL FRONT SEAT HEADREST SUPPORT (for LHD)
|
 |
- Engage the 2 claws to install the front seat headrest support.
- HINT:
- Use the same procedure for the RH side and LH side.
| 6.
INSTALL FRONT SEAT HEADREST SUPPORT (for RHD)
|
 |
- Engage the 2 claws to install the front seat headrest support.
- HINT:
- Use the same procedure for the RH side and LH side.
| 7.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for LHD)
|
 |
- Engage the 2 claws.
Engage the 14 claws.
Install the front seatback board sub-assembly with the 2 screws.
| 8.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for RHD) |
 |
for Except Sports Seat Type:
- Engage the 4 claws.
Install the front seatback board sub-assembly with the 2 screws.
for Sports Seat Type:
- Engage the 2 claws.
Engage the 14 claws.
Install the front seatback board sub-assembly with the 2 screws.
| 9.
INSTALL FRONT INNER SEAT CUSHION SHIELD (for LHD)
|
 |
- Install the front inner seat cushion shield with the screw.
Engage the 3 claws.
| 10.
INSTALL FRONT INNER SEAT CUSHION SHIELD (for RHD)
|
 |
- Engage the 3 claws.
Install the front inner seat cushion shield with the screw.
| 11.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY (for LHD)
|
 |
- Connect the connector.
Engage the 2 claws.
Install the front seat cushion shield assembly with the 5 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 12.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY (for RHD)
|
 |
Connect the connector.
- Engage the 2 claws.
Install the front seat cushion shield assembly with the 5 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 13.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for LHD)
|
 |
- Install the slide and vertical power seat switch knob.
| 14.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for RHD)
|
 |
- Install the slide and vertical power seat switch knob.
| 15.
INSTALL RECLINING POWER SEAT SWITCH KNOB (for LHD)
|
 |
- Install the reclining power seat switch knob.
| 16.
INSTALL RECLINING POWER SEAT SWITCH KNOB (for RHD)
|
 |
- Install the reclining power seat switch knob.
| 17.
INSTALL FRONT SEAT ASSEMBLY (for LHD)
|
 |
Place the seat in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
- Temporarily install the front side of the front seat assembly with the 2 bolts.
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
- Temporarily install the rear side of the front seat assembly with the 2 bolts.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 18.
INSTALL FRONT SEAT ASSEMBLY (for RHD)
|
 |
Place the seat in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
- Temporarily install the front side of the front seat assembly with the 2 bolts.
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
- Temporarily install the rear side of the front seat assembly with the 2 bolts.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 19.
INSTALL INNER SEAT TRACK BRACKET COVER (for LHD)
|
 |
- Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the inner seat track bracket cover to engage claw B.
| 20.
INSTALL INNER SEAT TRACK BRACKET COVER (for RHD)
|
 |
Engage the 4 claws and install the front seat rear inner track bracket cover.
| 21.
INSTALL OUTER SEAT TRACK BRACKET COVER (for LHD)
|
 |
- Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the seat track cover to engage claw B.
| 22.
INSTALL OUTER SEAT TRACK BRACKET COVER (for RHD)
|
 |
- Engage the 4 claws and install the front seat rear outer track bracket cover.
| 23.
INSTALL FRONT SEAT HEADREST ASSEMBLY (for LHD) |
|
| 24.
INSTALL FRONT SEAT HEADREST ASSEMBLY (for RHD) |
|
| 25.
INSPECT SRS WARNING LIGHT (w/ Airbag System) |
 |
Inspect the SRS warning light. (Click here)
| 26.
INSPECT FRONT SEAT ASSEMBLY |
|