2006-2011 Camry Aurion · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.

  1. B124520
    Using a "TORX" driver (T25), install the power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    The new rear window regulator adopts a self-tapping method. The installation position of the regulator will be threaded when the self-tapping screw is inserted.


2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.

  1. B136472E02
    Install the temporary bolt to the rear door window regulator sub-assembly.

  1. Temporarily install the window regulator.

  1. Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.


3. INSTALL REAR DOOR GLASS RUN

  1. B136466
    Install the rear door glass run.


4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

  1. B146104
    Slide the rear door glass sub-assembly to install it as shown in the illustration.


5. INSTALL REAR DOOR QUARTER WINDOW GLASS
  1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

  1. B136469
    Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY
  1. Insert the rear door lower window frame sub-assembly from above.

  1. Install the rear door glass run to the rear door lower window frame sub-assembly.

  1. B136467
    Install the rear door lower window frame sub-assembly with the 2 bolts and screw.


7. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.

  1. B149018E01
    Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

  1. Install the new rear door service hole cover.

    NOTICE:
    Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

  1. Connect the connector and clamp.


8. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

  1. B149019
    Engage the 3 claws to install the rear door inner glass weatherstrip.


9. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B136460
    Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle.

  1. B136453
    Engage the 2 claws and install the rear door inside handle sub-assembly.


10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B149020
    Engage the claw to install the No. 1 door scuff plate clamp.

  1. Connect each connector.

  1. B136452
    Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.

  1. B136451
    Engage the 7 clips to install the rear door trim board to the rear door panel.

  1. Install the 3 screws.


11. INSTALL REAR ASH RECEPTACLE ASSEMBLY (w/ Ashtray)

  1. B136442
    Install the rear ash receptacle assembly.


12. INSTALL DOOR ASSIST GRIP COVER

  1. B136448
    Engage the 6 claws and install the door assist grip cover.


13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B136444
    Engage the 3 claws to install the rear door inside handle bezel plug.


14. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)

15. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.

  1. B112321
    Using a "TORX" driver (T25), install the front power window regulator motor sub-assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator adopts a self-tapping method. The installation position of the regulator will be threaded when the self-tapping screw is inserted.


16. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

  1. B136415E02
    Install the temporary bolt to the front door window regulator sub-assembly.

  1. Temporarily install the window regulator.

  1. Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


17. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

  1. B136414E01
    Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.

  1. B136412
    Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


18. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable and rear door inside locking cable through a new front door service hole cover.

  1. B136411E01
    Install the new service hole cover.

    NOTICE:
    Securely install the front door service hole cover avoiding wrinkles and air bubbles.

  1. Connect each connector and each clamp.


19. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

  1. E129164
    Install the front No. 1 speaker assembly with the 4 bolts.

  1. Connect the connector.


20. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B136876
    Engage the 4 claws and install the front door inner glass weatherstrip.


21. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B136409
    Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. B136403
    Engage the 2 claws and install the front door inside handle sub-assembly.


22. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect each connector.

  1. B136402
    Engage the front door trim board with the 4 clips of the front door inner glass weatherstrip.

  1. B132840E01
    Engage the 9 clips and install the front door trim board to the front door panel.

  1. Install the 3 screws and clip (A).


23. INSTALL ASSIST GRIP COVER

  1. B132837
    Engage the 6 claws and install the assist grip cover.


24. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B132835
    Engage the 3 claws and install the front door inside handle bezel plug.


25. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B132833
    Engage the 2 clips and install the front door lower frame bracket garnish.


26. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)
← INSPECTION (from Jun 2006)INSTALLATION (Oct 2006 – May 2009) →