2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

FAIL-SAFE CHART

System information · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


Light control ECU (for HID headlight)
The light control ECU operates in the fail-safe mode if an abnormal condition such as those listed below has been detected.
Item
Outline
Detection of abnormal input voltage (High input voltage)
If voltage that is input to the light control ECU is approximately 20 V or more, the ECU stops illuminating the headlights, and resumes when the voltage drops to 16 V or less.
Detection of abnormal input voltage (Low input voltage)
If voltage that is input to the light control ECU is 6 V or less, the ECU stops illuminating the low beam headlights, and resumes when the voltage is 10 V or more.
Detection of abnormal output
  1. Output open
  2. Short between output terminals
  3. Short between output terminal and body ground
If an abnormal condition occurs in the voltage that is output by the light control ECU, the ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
Detection of bulb flashing
If the bulb flashing repeats within approximately 5 seconds and continues for approximately 60 seconds, the light control ECU stops illuminating low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
Detection of abnormal light voltage (Low light voltage)
After approximately 80 seconds since input voltage is supplied, if the light voltage is below approximately 31 V and continues for approximately 0.5 seconds, the light control ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
Detection of abnormal light voltage (High light voltage)
If the light voltage is above approximately 69 V and continues for approximately 0.5 seconds, the light control ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).

Headlight leveling ECU (without AFS)
  1. The headlight leveling ECU operates in the fail-safe mode if an abnormal condition such as those listed below has been detected.

    Item
    Abnormality Detection Condition
    Return Condition
    Warning Indicator
    Height control sensor power source voltage
    Abnormal height control sensor power source voltage (4.6 V or less) is detected.
    Normal voltage is detected 50 times consecutively
    Illuminated
    Height control sensor signal voltage
    Abnormal height control sensor signal voltage (0.25 V or less, or 4.75 V or more) is detected.
    High power source voltage
    Abnormal high ignition voltage (18.5 V or less) is detected.
    Voltage of 17.5 V or less is detected
    Not illuminated
    Low power source voltage
    Abnormal low ignition voltage (9.0 V or less) is detected.
    Voltage of 9.3 V or more is detected for 0.1 second consecutively
    Not illuminated
    Vehicle speed
    Abnormal high speed (180 km/h or more) is detected.
    Speed of less than 175 km/h (109 mph) is detected
    Not illuminated
    Reset while running
    Reset by a temporary blackout, etc. while running.
    Vehicle is stopped
    Not illuminated


AFS ECU
If the AFS ECU detects a malfunction in the automatic headlight beam level control system or intelligent AFS, it will take the actions indicated in the table below.
Fail-Safe Control for Automatic Headlight Beam Level Control: 
Trouble Area
Condition
AFS OFF Indicator Light
Headlight Swivel Motor Malfunction
Continues to control until a position of 0.8° less than the current position is reached.
Flash
Steering Angle Sensor Signal Malfunction
Continues to control.
Flash
Speed Sensor Signal Malfunction
  1. Continues to control using the normal speed sensor signal if one signal fails.
  2. Judges that the vehicle speed is 0 km/h and continues to control if both speed sensor signals fail.
Flash
Height Control Sensor Signal Malfunction
  1. Stops the operation after returning to initial position (Fail at higher than initial position).
  2. Stops the operation in current condition (Fail at lower than initial position).
Flash
Headlight Leveling Motor Malfunction
Normal Side Headlight Leveling Motor
  1. Stops the operation after returning to initial position (Fail at higher than initial position).
  2. Stops in current condition (Fail at lower than initial position).
Flash
Abnormal Side Headlight Leveling Motor
  1. Stops in its current position.
Communication Signal Malfunction
Skid Control ECU:
  1. Judges that the vehicle speed is 0 km/h (0 mph) and continues to control.
Flash
Steering Angle Sensor:
  1. Continues to control.
Fail-Safe Control for Intelligent AFS: 
Trouble Area
Condition
AFS OFF Indicator Light
Headlight Swivel Motor
Normal Side Headlight Swivel Motor:
  1. Stops operating after returning to the initial position.
Flash
Abnormal Side Headlight Swivel Motor:
  1. Stops in its current position.
Steering Angle Sensor Signal Malfunction
Stops operating after returning to the initial position.
Flash
Speed Sensor Signal Malfunction
Stops operating after returning to the initial position.
Flash
Height Control Sensor Signal Malfunction
Stops operating after returning to the initial position.
Flash
Headlight Leveling Motor
Stops operating after returning to the initial position.
Flash
Communication Signal Malfunction
Main Body ECU:
  1. Stops operating after returning to the initial position.
Flash
Engine ECU:
  1. Stops operating after returning to the initial position.
Skid Control ECU:
  1. Stops operating after returning to the initial position.
Steering Angle Sensor:
  1. Stops operating after returning to the initial position.
← DTC CHECK / CLEAR (from Oct 2006)FAIL-SAFE CHART (from Jun 2009) →