2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

FAIL-SAFE CHART

System information · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


Light control ECU (for HID headlight)
The light control ECU operates in the fail-safe mode if an abnormal condition such as those listed below has been detected.
Item
Outline
Detection of abnormal input voltage (High input voltage)
If voltage that is input to the light control ECU is approximately 20 V or more, the ECU stops illuminating the headlights, and resumes when the voltage drops to 16 V or less.
Detection of abnormal input voltage (Low input voltage)
If voltage that is input to the light control ECU is 6 V or less, the ECU stops illuminating the low beam headlights, and resumes when the voltage is 10 V or more.
Detection of abnormal output
  1. Output open
  2. Short between output terminals
  3. Short between output terminal and body ground
If an abnormal condition occurs in the voltage that is output by the light control ECU, the ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
Detection of abnormal light voltage (Low light voltage)
After approximately 80 seconds since input voltage is supplied, if the light voltage is below approximately 31 V and continues for approximately 0.5 seconds, the light control ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
Detection of abnormal light voltage (High light voltage)
If the light voltage is above approximately 69 V and continues for approximately 0.5 seconds, the light control ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).

AFS ECU
If the AFS ECU detects a malfunction in the automatic headlight beam level control system or intelligent AFS, it will take the actions indicated in the table below.
Fail-Safe Control for Automatic Headlight Beam Level Control: 
Trouble Area
Condition
AFS OFF Indicator Light
Headlight Swivel Motor Malfunction
Continues to control until a position of 0.65° less than the current position is reached.
Flashes
Steering Angle Sensor Signal Malfunction
Continues to control.
Flashes
Speed Sensor Signal Malfunction
  1. Continues to control using the normal speed sensor signal if one signal fails.
  2. Judges that the vehicle speed is 0 km/h (0 mph) and continues to control if both speed sensor signals fail.
Flashes
Height Control Sensor Signal Malfunction
  1. Stops the operation after returning to initial position (Fail at higher than initial position).
  2. Stops the operation in current condition (Fail at lower than initial position).
Flashes
Headlight Leveling Motor Malfunction
Normal Side Headlight Leveling Motor
  1. Stops the operation after returning to initial position (Fail at higher than initial position).
  2. Stops in current condition (Fail at lower than initial position).
Flashes
Abnormal Side Headlight Leveling Motor
  1. Stops in its current position.
Communication Signal Malfunction
Skid Control ECU:
  1. Judges that the vehicle speed is 0 km/h (0 mph) and continues to control.
Flashes
Steering Angle Sensor:
  1. Continues to control.
Fail-Safe Control for Intelligent AFS: 
Trouble Area
Condition
AFS OFF Indicator Light
Headlight Swivel Motor
Normal Side Headlight Swivel Motor:
  1. Stops operating after returning to the initial position.
Flashes
Abnormal Side Headlight Swivel Motor:
  1. Stops in its current position.
Steering Angle Sensor Signal Malfunction
Stops operating after returning to the initial position.
Flashes
Speed Sensor Signal Malfunction
Stops operating after returning to the initial position.
Flashes
Height Control Sensor Signal Malfunction
Stops operating after returning to the initial position.
Flashes
Headlight Leveling Motor
Stops operating after returning to the initial position.
Flashes
Communication Signal Malfunction
Main Body ECU:
  1. Stops operating after returning to the initial position.
Flashes
Engine ECU:
  1. Stops operating after returning to the initial position.
Skid Control ECU:
  1. Stops operating after returning to the initial position.
Steering Angle Sensor:
  1. Stops operating after returning to the initial position.
← FAIL-SAFE CHART (Oct 2006 – May 2009)DATA LIST / ACTIVE TEST (Oct 2006 – May 2009) →