2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

INITIALIZATION

Troubleshooting · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION

NOTICE:
  1. Initialize the height control sensor signal after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor sub-assembly.
  2. When the headlight leveling ECU or AFS ECU is replaced, the initialization is also necessary.
  3. Adjust the headlight aim after initializing the headlight leveling ECU or AFS ECU (Click here).
  1. When a malfunction is detected in the automatic headlight beam level control system, the height control sensor signal initialization is impossible. Perform troubleshooting before initialization.


1.PREPARE VEHICLE FOR INITIALIZATION
  1. Make sure that approximately 10 liters of fuel is in the tank.

  2. Unload the trunk and vehicle, ensuring that the spare tire, tools, and jack are in their original positions.

  3. Check that there are no passengers in the vehicle.

  4. Turn off the headlights.

NEXT

2.CHECK WARNING LIGHT

  1. Turn the ignition switch on (IG), and check the headlight beam level control system warning light or AFS indicator light.E133293E01

    OK:
    Condition
    Specified Condition
    The headlight leveling ECU or AFS ECU is replaced with a new one.
    Warning light continuously blinks twice at 2 Hz as shown in the illustration.
    Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, or replacement of the suspension, etc.
    Warning light comes on for approximately 3 seconds, and then goes off (bulb check function).

    HINT:
    When the AFS OFF switch is on (pushed), the warning light comes on.

    HINT:
    1. If the warning light does not come on when turning the ignition switch on (IG), inspect and repair according to "PROBLEM SYMPTOMS TABLE" (Click here).
    2. If there is a problem with initialized data memorized in the headlight leveling ECU or AFS ECU, the warning light blinks twice at 2 Hz as shown in the illustration when the ignition switch is turned on (IG).


NG.
OK

3.INITIALIZATION

  1. E106867E12
    Connect terminals 4 (CG) and 8 (LVL) of the DLC3 using SST.

  2. SST
    09843-18040  
  3. Flash the low beam headlights 3 times or more by turning the light control switch within 20 seconds after connecting the terminals.

    NOTICE:
    1. Turn the low beam headlights on or off at approximately 1-second intervals.
    2. Be sure to operate the light control switch from the outside of the vehicle.

  4. E121525E01
    Check the warning light.

    OK:
    Condition
    Specified Condition
    The headlight leveling ECU or AFS ECU is replaced with a new one.
    Blinks twice at 2 Hz → Blinks 3 times at 2 Hz, and then goes off (refer to illustration 1).
    Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, or replacement of the suspension, etc.
    Off → Blinks 3 times at 2 Hz, and then goes off (refer to illustration 2).

    HINT:
    When the AFS OFF switch is on (pushed), the warning light comes on.

    HINT:
    1. If calculated vehicle height is not between full-bound and full-rebound, the height control sensor initialization will end as abnormal termination, and the warning indicator will blink twice at 2 Hz continuously as shown in illustration 3. Disconnect the SST from the DLC3 and turn the ignition switch off. Then, restart from procedure 2.
    2. If initialization cannot be finished normally, check the LVL terminal circuit (Click here), or inspect and repair according to "PROBLEM SYMPTOMS TABLE" (Click here).


NG.
OK

← CUSTOMIZE PARAMETERS (from Oct 2006)INITIALIZATION (from Jun 2009) →