B2326 CAN MS Bus Line Communication Malfunction
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
- The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
- When the main body ECU receives response signals from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECUs are connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2326 |
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- HINT:
- Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
- For vehicles equipped with the mayday system, inspect the mayday system.
- Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK CAN MS BUS WIRE |
Turn the engine switch off.

Measure the resistance according to the value(s) in the table below.
- Result:
Tester Connection
Condition
Specified Value
Proceed to
O34-1 (CANH) - O34-2 (CANL)
Engine switch off
54 to 69 Ω
A
O34-1 (CANH) - O34-2 (CANL)
Engine switch off
69 Ω or higher
B
O34-1 (CANH) - O34-2 (CANL)
Engine switch off
Below 54 Ω
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
O34-2 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O34-2 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
|
|
||||
| OK | |
| 4. CHECK FOR OPEN IN CAN MS BUS BRANCH WIRE |
Check for an open in the branch wires of all ECUs connected to the CAN MS bus.
Check the outer mirror control ECU branch wire (Click here).
Check the seat position control ECU (front LH side) branch wire (Click here)
Check the clearance warning ECU branch wire (Click here).
- Result:
Result
Proceed to
OK
A
NG
B
|
|
||||
| A | ||
| ||
| 5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU MAIN WIRE) |
Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

- HINT:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - O34-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| NG | |
| 6. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.
Disconnect certification ECU connector E58.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| NG | ||
| ||
| 7. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

- HINT:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - O33-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| NG | |
| Go to step 9 |
| 8. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 5 J/C) |
Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.
Disconnect connector E8 from the main body ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Engine switch off
108 to 132 Ω
- Result:
Result
Proceed to
OK
A
NG (without Seat position memory system)
B
NG (with Seat position memory system)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 9. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 5 J/C WIRES) |
Reconnect main body ECU main wire connector E8.
Disconnect CAN No. 5 J/C connector E81.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E81-10 (CANH) - E81-21 (CANL)
Engine switch off
108 to 132 Ω
E81-11 (CANH) - E81-22 (CANL)
Engine switch off
108 to 132 Ω
- Result:
Result
Defective Wire
Proceed to
OK
-
A
NG
Wire for main body ECU
B
NG
Wire for CAN No. 3 J/C
C
|
|
||||
|
|
||||
| B | ||
| ||
| 10. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C WIRE) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - O33-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| OK | |
| 11. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU MAIN WIRE) |
Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

- HINT:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - O34-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| NG | |
| 12. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU - CAN NO. 3 J/C) |
Disconnect certification ECU connector E58.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 13. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE) |
Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.
Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

- HINT:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - O32-2 (CANL)
Engine switch off
1 MΩ or higher
|
|
||||
| NG | |
| 14. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE) |
Disconnect clearance warning ECU connector O30.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - O32-2 (CANL)
Engine switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 15. CHECK FOR SHORT IN CAN MS BUS WIRES (MAIN BODY ECU MAIN WIRE) |
Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.
Disconnect the main body ECU main wire connector E8.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Engine switch off
108 to 132 Ω
- Result:
Result
Proceed to
OK
A
NG (without Seat position memory system)
B
NG (with Seat position memory system)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 16. CHECK FOR SHORT IN CAN MS BUS WIRES (FOR CAN NO. 5 J/C) |


Disconnect CAN No. 5 J/C connector E81.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E81-8 (CANH) - E81-19 (CANL)
Engine switch off
1 MΩ or higher
E81-9 (CANH) - E81-20 (CANL)
Engine switch off
1 MΩ or higher
E81-10 (CANH) - E81-21 (CANL)
Engine switch off
1 MΩ or higher
E81-11 (CANH) - E81-22 (CANL)
Engine switch off
108 to 132 Ω
- Result:
Result
Defective Terminal
Proceed to
OK
-
A
NG
E81-10 (CANH) - E81-21 (CANL)
B
NG
E81-8 (CANH) - E81-19 (CANL)
E81-9 (CANH) - E81-20 (CANL)
E81-11 (CANH) - E81-22 (CANL)
C
|
|
||||
|
|
||||
| C | |
| 17. CHECK FOR SHORT IN CAN MS BUS WIRES |
Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.
Recheck the short-circuited wire with the connector disconnected from the ECU.
- Standard:
- The wire is not short-circuited.
- HINT:
- If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short-circuit is suspected.
|
|
||||
| OK | ||
| ||
| 18. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
O33-2 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
|
|
||||
| OK | |
| 19. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
O34-2 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
|
|
||||
| OK | |
| 20. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C) |
Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.
Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

Disconnect clearance warning ECU connector O30.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
O32-2 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 21. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
Disconnect certification ECU connector E58.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
O34-2 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 22. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (MAIN BODY ECU MAIN WIRE) |
Reconnect the CAN MS bus main wire connector O33.
Disconnect the main body ECU connector E8.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E8-15 (CANN) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
- Result:
Result
Proceed to
OK
A
NG (without Seat position memory system)
B
NG (with Seat position memory system)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 23. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 5 J/C WIRE) |


Disconnect CAN No. 5 J/C connector E81.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
E81-11 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E81-22 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E81-10 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E81-21 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E81-9 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E81-20 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E81-8 (CANH) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
E81-19 (CANL) - E10-16 (BAT)
Engine switch off
6 kΩ or higher
- Result:
Result
Defective Wire
Proceed to
NG
E81-11, E81-22, E81-9, E81-20, E81-8 or E81-19
A
NG
E81-10 or E81-21
B
|
|
||||
| A | |
| 24. CHECK SHORT TO +B IN CAN MS BUS WIRE |
Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.
Recheck the short-circuited wire with the connector disconnected from the ECU.
- Standard:
- The wire is not short-circuited.
- HINT:
- If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short circuit is suspected.
|
|
||||
| OK | ||
| ||
| 25. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O33-2 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
|
|
||||
| OK | |
| 26. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O34-2 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
|
|
||||
| OK | |
| 27. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C) |
Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.
Disconnect clearance warning ECU connector O30.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O32-2 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
|
|
||||
| OK | ||
| ||
| 28. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
Disconnect certification ECU connector E58.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O34-2 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
|
|
||||
| OK | ||
| ||
| 29. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (MAIN BODY ECU MAIN WIRE) |
Reconnect the CAN MS bus main wire connector O33.
Disconnect the main body ECU connector E8.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E10-4 (CG)
Engine switch off
6 kΩ or higher
E8-15 (CANN) - E10-4 (CG)
Engine switch off
6 kΩ or higher
- Result:
Result
Proceed to
OK
A
NG (without Seat position memory system)
B
NG (with Seat position memory system)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 30. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 5 J/C WIRE) |


Disconnect CAN No. 5 J/C connector E81.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
E81-11 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
E81-22 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
E81-10 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
E81-21 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
E81-9 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
E81-20 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
E81-8 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
E81-19 (CANL) - E10-4 (CG)
Engine switch off
200 Ω or higher
- Result:
Result
Defective Wire
Proceed to
NG
E81-11, E81-22, E81-9, E81-20, E81-8 or E81-19
A
NG
E81-10 or E81-21
B
|
|
||||
| A | |
| 31. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE |
Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.
Recheck the short-circuited wire with the connector disconnected from the ECU.
- Standard:
- The wire is not short-circuited.
- HINT:
- If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short circuit is suspected.
|
|
||||
| OK | ||
| ||
