2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B2326 CAN MS Bus Line Communication Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

  1. The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
  2. When the main body ECU receives response signals from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECUs are connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
DTC No.
DTC Detection Condition
Trouble Area
B2326
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus.
  1. Open or short in CAN MS bus main wire or connector
  2. Open or short in CAN MS bus branch wire or connector
  3. Certification ECU
  4. Seat position control ECU (Front RH side)
  5. Outer mirror control ECU
  6. Clearance warning ECU
  7. Mayday ECU
  8. Main body ECU
  9. CAN No. 3 J/C
  10. CAN No. 5 J/C
  11. CAN No. 6 J/C

WIRING DIAGRAM

C213915E01
C213914E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK CAN MS BUS WIRE
  1. Turn the engine switch off.

  1. B139430E26
    Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Condition
    Specified Value
    Result
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    54 to 69 Ω
    Below 54 Ω:
    Short circuit between bus wires
    70 Ω or higher:
    Open circuit bus main wire
    E58-27 (CANH) - E58-17 (E)
    Engine switch off
    200 Ω or higher
    Below 200 Ω:
    CANH ground short
    E58-28 (CANL) - E58-17 (E)
    Engine switch off
    200 Ω or higher
    Below 200 Ω:
    CANL ground short

  1. Disconnect the cable from the negative (-) battery terminal.

  1. B139430E27
    Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Condition
    Specified Value
    Result
    E58-27 (CANH) - E58-1 (+B)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANH +B short
    E58-28 (CANL) - E58-1 (+B)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANH +B short

    Result:
    Result
    Proceed to
    OK (w/ seat position memory)
    A
    OK (w/o seat position memory)
    B
    NG (open circuit bus main wire)
    C
    NG (short circuit between bus wires)
    D
    NG (short to ground or short to +B)
    E



B
Go to step 2

C
Go to step 5

D
Go to step 11

E
Go to step 19
A

REPLACE MAIN BODY ECU

Go to step 3

2. CHECK ECU POWER SOURCE CIRCUIT (CERTIFICATION ECU)
  1. Check the certification ECU power source circuit (Click here).



NG
REPAIR OR REPLACE WIRE HARNESS (CERTIFICATION ECU POWER SOURCE CIRCUIT)
OK


3. REPLACE MAIN BODY ECU
  1. Replace the main body ECU.


NEXT


4. RECONFIRM DTC OUTPUT
  1. Check the DTC.

    Result:
    Result
    Proceed to
    B2326 not output
    A
    B2326 output
    B



B
REPLACE CERTIFICATION ECU
A

END

5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU)

  1. C142197E03
    Disconnect the certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω



NG
Go to step 6
OK

REPLACE CERTIFICATION ECU

6. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU)
  1. Reconnect the certification ECU connector E58.

  1. C142209E03
    Disconnect the main body ECU connector E8.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/ Seat position memory)
    B
    NG (w/o Seat position memory)
    C



B
Go to step 7

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)
A

REPLACE MAIN BODY ECU

Go to step 3

7. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 5 J/C)
  1. Reconnect the main body ECU connector E8.

  1. Disconnect the CAN No. 5 J/C wire harness connector.C142785E24

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    Connected to
    E81-10 (CANH) - E81-21 (CANL)
    Engine switch off
    108 to 132 Ω
    CAN No. 3 J/C
    E81-11 (CANH) - E81-22 (CANL)
    Engine switch off
    108 to 132 Ω
    Main body ECU*1
    or
    CAN No. 6 J/C*2

    *1: w/o Toyota link system*2: w/ Toyota link system

    Result:
    Result
    Proceed to
    OK
    A
    NG (to CAN No. 3 J/C)
    B
    NG (to Main body ECU)
    C
    NG (to CAN No. 6 J/C)
    D



B
Go to step 8

C
Go to step 12

D
Go to step 10
A

REPLACE CAN NO. 5 J/C

8. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 5 J/C - CAN NO. 3 J/C)
  1. Reconnect the CAN No. 5 J/C wire harness connector.

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

    HINT:
    O33 connector color: White

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
NG


9. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO.3 J/C - CERTIFICATION ECU)
  1. Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C142738E01
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

    HINT:
    O34 connector color: Gray

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU - CAN NO. 3 J/C)
OK

REPLACE CAN NO. 3 J/C

10. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 6 J/C)
  1. Reconnect the CAN No. 5 J/C wire harness connector.

  1. Disconnect the CAN No. 6 J/C wire harness connector.C188960E06

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    Connected to
    N40-1 (CANH) - N40-6 (CANL)
    Engine switch off
    108 to 132 Ω
    CAN No. 5 J/C
    N40-2 (CANH) - N40-7 (CANL)
    Engine switch off
    108 to 132 Ω
    Main body ECU

    Result:
    Result
    Proceed to
    OK
    A
    NG (to Main body ECU)
    B
    NG (to CAN No. 5 J/C)
    C



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CAN NO. 6 J/C)

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 6 J/C - CAN NO. 5 J/C)
A

REPLACE CAN NO. 6 J/C

11. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU)

  1. C142197E03
    Disconnect the certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω



NG
Go to step 12
OK

REPLACE CERTIFICATION ECU

12. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
  1. Reconnect the certification ECU connector E58.

  1. C142209E03
    Disconnect the main body ECU connector E8.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/ Seat position memory)
    B
    NG (w/o Seat position memory)
    C



B
Go to step 13

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)
A

REPLACE MAIN BODY ECU

Go to step 3

13. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 5 J/C)
  1. Reconnect main body ECU connector E8.

  1. Disconnect the CAN No. 5 J/C wire harness connector.C142785E23

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    Connected to
    E81-8 (CANH) - E81-19 (CANL)
    Engine switch off
    1 Ω or higher
    Outer mirror control ECU
    E81-9 (CANH) - E81-20 (CANL)
    Engine switch off
    1 Ω or higher
    Seat position control ECU
    E81-10 (CANH) - E81-21 (CANL)
    Engine switch off
    108 to 132 Ω
    CAN No. 3 J/C
    E81-11 (CANH) - E81-22 (CANL)
    Engine switch off
    108 to 132 Ω
    Main body ECU*1
    or
    CAN No. 6 J/C*2

    *1: w/o Toyota link system*2: w/ Toyota link system

    Result:
    Result
    Proceed to
    OK
    A
    NG (to CAN No. 3 J/C)
    B
    NG (to Main body ECU)
    C
    NG (to CAN No. 6 J/C)
    D
    NG (to Outer mirror control ECU or seat position control ECU)
    E



B
Go to step 14

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 5 J/C - MAIN BODY ECU)

D
Go to step 17

E
Go to step 18
A

REPLACE CAN NO. 5 J/C

14. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 5 J/C - CAN NO. 3 J/C)
  1. Reconnect the CAN No. 5 J/C wire harness connector.

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

    HINT:
    O33 connector color: White

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
NG


15. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C - CERTIFICATION ECU)
  1. Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C142738E01
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

    HINT:
    O34 connector color: Gray

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU - CAN NO. 3 J/C)
OK


16. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE)
  1. Reconnect the CAN MS bus main wire connector O34 to the CAN No. 3 J/C.

  1. C142740E01
    Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

    HINT:
    O32 connector color: Blue

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - O32-2 (CANL)
    Engine switch off
    1 Ω or higher



NG
Go to step 18

C
Go to step 17
OK

REPLACE CAN NO. 3 J/C

17. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 6 J/C)
  1. Reconnect the CAN No. 5 J/C wire harness connector.

  1. Disconnect the CAN No. 6 J/C wire harness connector.C188960E05

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    Connected to
    N40-1 (CANH) - N40-6 (CANL)
    Engine switch off
    108 to 132 Ω
    Main body ECU
    N40-2 (CANH) - N40-7 (CANL)
    Engine switch off
    108 to 132 Ω
    CAN No. 5 J/C
    N40-3 (CANH) - N40-8 (CANL)
    Engine switch off
    1 Ω or higher
    Mayday ECU

    Result:
    Result
    Proceed to
    OK
    A
    NG (to CAN No. 5 J/C)
    B
    NG (to Main body ECU)
    C
    NG (to Mayday ECU)
    D



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 6 J/C - CAN NO. 5 J/C)

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CAN NO. 6 J/C)

D
Go to step 18
A

REPLACE CAN NO. 6 J/C

18. CHECK FOR SHORT IN CAN MS BUS WIRES (ECU)
  1. Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.

  1. Recheck the short-circuited wire with the connector disconnected from the ECU.

    Standard:
    The wire is not short-circuited.

    HINT:
    If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short-circuit is suspected.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR

19. CHECK FOR SHORT IN CAN MS BUS WIRE (CERTIFICATION ECU)

  1. C136713E15
    Measure the resistance according to the value(s) in the table below.

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.


    Standard resistance:
    Check for CAN Bus Wire Short to Ground 
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-17 (E)
    Engine switch off
    200 Ω or higher
    E58-28 (CANL) - E58-17 (E)
    Check for CAN Bus Wire Short to +B 
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-1 (+B)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E58-28 (CANL) - E58-1 (+B)



NG
Go to step 20
OK

REPLACE CERTIFICATION ECU

20. CHECK FOR SHORT IN CAN MS BUS WIRE (MAIN BODY ECU)

  1. C142209E03
    Disconnect the main body ECU connector E8.

  1. C126231E41
    Measure the resistance according to the value(s) in the table below.

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.


    Standard resistance:
    Check for CAN Bus Wire Short to Ground 
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E8-15 (CANN) - E10-4 (CG)
    Check for CAN Bus Wire Short to +B 
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E8-15 (CANN) - E10-16 (BAT)

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/ Seat position memory)
    B
    NG (w/o Seat position memory)
    C



B
Go to step 21

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)
A

REPLACE MAIN BODY ECU

Go to step 3

21. CHECK FOR SHORT IN CAN MS BUS WIRE (CAN NO. 5 J/C)

  1. Disconnect the CAN No. 5 J/C wire harness connector.C142785E23

  1. C126231E41
    Measure the resistance according to the value(s) in the table below.

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.


    Standard resistance:
    Check for CAN Bus Wire Short to Ground 
    Tester Connection
    Condition
    Specified Value
    Connected to
    E81-8 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    Outer mirror control ECU
    E81-19 (CANL) - E10-4 (CG)
    E81-9 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    Seat position control ECU
    E81-20 (CANL) - E10-4 (CG)
    E81-10 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    CAN No. 3 J/C
    E81-21 (CANL) - E10-4 (CG)
    E81-11 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    Main body ECU*1
    or
    CAN No. 6 J/C
    E81-22 (CANL) - E10-4 (CG)
    Check for CAN Bus Wire Short to +B 
    Tester Connection
    Condition
    Specified Value
    Connected to
    E81-8 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Outer mirror control ECU
    E81-19 (CANL) - E10-16 (BAT)
    E81-9 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Seat position control ECU
    E81-20 (CANL) - E10-16 (BAT)
    E81-10 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    CAN No. 3 J/C
    E81-21 (CANL) - E10-16 (BAT)
    E81-11 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Main body ECU*1
    or
    CAN No. 6 J/C
    E81-22 (CANL) - E10-16 (BAT)

    *1: w/o Toyota link system*2: w/ Toyota link system

    Result:
    Result
    Proceed to
    OK
    A
    NG (to CAN CAN No. 3 J/C)
    B
    NG (to Main body ECU)
    C
    NG (to CAN No. 6 J/C)
    D
    NG (to Outer mirror control ECU or seat position control ECU)
    E



B
Go to step 22

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 5 J/C - MAIN BODY ECU)

D
Go to step 25

E
Go to step 26
A

REPLACE CAN NO. 5 J/C

22. CHECK FOR SHORT IN CAN MS BUS WIRE (CAN NO. 5 J/C - CAN NO. 3 J/C)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

    HINT:
    O33 connector color: White

  1. C126231E41
    Measure the resistance according to the value(s) in the table below.

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.


    Standard resistance:
    Check for CAN Bus Wire Short to Ground 
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O33-2 (CANL) - E10-4 (CG)
    Check for CAN Bus Wire Short to +B 
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    O33-2 (CANL) - E10-16 (BAT)



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
OK


23. CHECK FOR SHORT IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 5 J/C)

  1. C142738E01
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

    HINT:
    O34 connector color: Gray

HINT:
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.

  1. C126231E41
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for CAN Bus Wire Short to Ground 
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O34-2 (CANL) - E10-4 (CG)
    Check for CAN Bus Wire Short to +B 
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    O34-2 (CANL) - E10-16 (BAT)



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU - CAN NO. 3 J/C)
OK


24. CHECK FOR SHORT IN CAN MS BUS WIRE (CLEARANCE WARNING ECU BRANCH WIRE)

  1. C142740E01
    Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

    HINT:
    O32 connector color: Blue

  1. C126231E41
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for CAN Bus Wire Short to Ground 
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O32-2 (CANL) - E10-4 (CG)
    Check for CAN Bus Wire Short to +B 
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    O32-2 (CANL) - E10-16 (BAT)



NG
Go to step 26
OK

REPLACE CAN NO. 3 J/C

25. CHECK FOR SHORT IN CAN MS BUS WIRE (CAN NO. 6 J/C)

  1. Disconnect the CAN No. 6 J/C wire harness connector.C188960E05

  1. C126231E41
    Measure the resistance according to the value(s) in the table below.

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.


    Standard resistance:
    Check for CAN Bus Wire Short to Ground 
    Tester Connection
    Condition
    Specified Value
    Connected to
    N40-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    Main body ECU
    N40-6 (CANL) - E10-4 (CG)
    N40-2 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    CAN No. 5 J/C
    N40-7 (CANL) - E10-4 (CG)
    E81-3 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    Mayday ECU
    E81-8 (CANL) - E10-4 (CG)
    Check for CAN Bus Wire Short to +B 
    Tester Connection
    Condition
    Specified Value
    Connected to
    N40-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Main body ECU
    N40-6 (CANL) - E10-16 (BAT)
    N40-2 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    CAN No. 5 J/C
    N40-7 (CANL) - E10-16 (BAT)
    N40-3 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Mayday ECU
    N40-8 (CANL) - E10-16 (BAT)

    Result:
    Result
    Proceed to
    OK
    A
    NG (to CAN CAN No. 5J/C)
    B
    NG (to Main body ECU)
    C
    NG (to Mayday ECU)
    D



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 6 J/C - CAN NO. 5 J/C)

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CAN NO. 6 J/C)

D
Go to step 26
A

REPLACE CAN NO. 6 J/C

26. CHECK FOR SHORT IN CAN MS BUS WIRE (ECU)
  1. Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.

  1. Recheck the short-circuited wire with the connector disconnected from the ECU.

    Standard:
    The wire is not short-circuited.

    HINT:
    If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short circuit is suspected.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR


← B2326 CAN MS Bus Line Communication Malfunction (Oct 2006 – May 2009)U0182 Lost Communication with AFS ECU (from Oct 2006) →